Sale!

Polyurethane and epoxy Injection Equipment

$0.01

Category:

Polyurethane and epoxy Injection Equipment

Item: Polyurethane and epoxy Injection Equipment

  • Working pressure: instantaneous pressure can be up to 10000Psi (700 kg / cm2) (the maximum working pressure is 500 kg,it is strictly prohibited to more than 700 kg), flow rate: 0.74 liters / minute, chemical pulp can enter hairline cracks which is more than 0.02mm,deep up to 1000mm.
  • Mechanical properties and stability: according to operating procedures, use injection packers,it can be continuous, efficient and safe wrok.
  • Easy to operate: small size, light weight, easy handling, cleaning, maintenance, 220V power supply connection.
    Applicable perfusion material: soluble polyurethane sealing agent, oil-soluble polyurethane sealing agent, epoxy potting, acrylic resin infusion materials and other non-granular, low viscosity slurry.

Models: KAY-,KAY-B,KAY-C,KAY-C+,KAY-999

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Polyurethane and epoxy Injection Equipment
 Characteristic for “Polyurethane and epoxy Injection Equipment”

Injection-pump-equipment

Description:
The Polyurethane and epoxy Injection Equipment is a machine kit for construction and chemical grouting plugging structures, and structural reinforcement.

Features:

  • Working pressure: instantaneous pressure can be up to 10000Psi (700 kg / cm2) (the maximum working pressure is 500 kg,it is strictly prohibited to more than 700 kg), flow rate: 0.74 liters / minute, chemical pulp can enter hairline cracks which is more than 0.02mm,deep up to 1000mm.
  • Mechanical properties and stability: according to operating procedures, use injection packers,it can be continuous, efficient and safe wrok.
  • Easy to operate: small size, light weight, easy handling, cleaning, maintenance, 220V power supply connection.
    Applicable perfusion material: soluble polyurethane sealing agent, oil-soluble polyurethane sealing agent, epoxy potting, acrylic resin infusion materials and other non-granular, low viscosity slurry.
  • Environment protection: Good mechanical performance, no noise and no pollution.
  • Portable: Small, light, convenience, and easy to handle.
  • Safety: With credible techniques and reasonable structure, you can use it safely.
  • No damage to structure: Install injector directly to grout, no need to lay pipes and trough.
  • In the case of streaming from aperture, comb and underground, it can grout in water, grouting material may go deep into the crack effectively.

Usage:

  • A variety of buildings and underground concrete cracks, expansion joints, construction joints, structural joints sealed plugging.
  •  Geological drilling engineering drilling wall plugging reinforcement.
  • Water conservancy and Hydropower Project reservoir dam grouting, plugging cracks in the tunnel water, waterproof, impervious dam reinforced concrete cracks.
  • High rise buildings and railroad, Highway Roadbed Stabilization.
  •  Coal mining and other mining engineering of tunnel water plugging, roof breaking layer reinforcement.
  •  Bridge foundation reinforcement and the bridge body crack of reinforcement.
  • Deformed Reinforcement of buildings, concrete structures such as the Water Tower, pool crevice reinforcement and prevent subsidence.
  • Soil improvement, soil surface protection and stability reinforcement.

Note:
When using the two-component liquid grout, the material curing time must be mastered before the infusion, to prevent slurry cured within the machine.

A machine with multi function: plugging grouting, soft ground consolidation grouting reinforcement structure for dry crack grouting.
Single-phase AC 220V / 50Hz.

Instructions for use:

Correct electrical connection: the machine need to use 220V AC, 380V AC power is not available.

The components to maintain normal:
Always lock the parts screw machines, drills must be fully inserted into the holder, not loose.
High-pressure and high-pressure pipe and the main body of the perfusion machine gun coupled with raw material must be wrapped and tighten to prevent leakage of plasma.
Gauges need normal reaction. Construction, such as the hands not properly lift, after the table now be replaced with new construction.

Prohibitions:
When grouting is strictly prohibited and-click switching power supply; prohibited under the pressure of more than 200 kg in the case of the second start; continue Grouting shall not exceed 700 kg of pressure situations.
Do perfusion slurry particulate ingredients, such as resin mortar, cement, non-shrink cement.
Does not prohibit the use of viscous liquids such as (toluene, acetone, water, etc.) Working Pressure Test

 Models and details for “Polyurethane and epoxy Injection Equipment”

Single-phase AC 220V / 50Hz.

Working pressure: instantaneous pressure can be up to 10000Psi (700 kg / cm2) (the maximum working pressure is 500 kg,it is strictly prohibited to more than 700 kg),;

Flow rate: 0.74 liters / minute, chemical pulp can enter hairline cracks which is more than 0.02mm,deep up to 1000mm.

KAY-A,motor power: 650W

KAY-A

KAY-B,motor power: 650W

KAY-B

KAY-C,motor power: 810W

KAY-C

KAY-C+,motor power: 810W(Has a handle to adjust pressure)

KAY-C

KAY-999,motor power:810W

KAY-999

 

Buying Guide to “Polyurethane and epoxy Injection Equipment”
  • The Injection equipment is available for retail and wholesale;
  • The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
  • Accept bulk order with Container delivery;
  • More types of  injection pump equipments are not displayed on the web.If the item above doesn`t meet your requirement,please contact us to email: ventilation@smartclima.com ,we can supply a favourite item you need.
General Knowledge on “Polyurethane and epoxy Injection Equipment ”

Enquiry or Reviews

There are no reviews yet.

Be the first to review “Polyurethane and epoxy Injection Equipment”

Rate Your Satisfaction*