Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner

Chiller tube cleaning nylon brush,Spiral tube brush for condenser heat exchanger tube cleaner

Item:Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner

Brief Description: brush for Chiller tube cleaning,total length  165mm,brush part long 100mm,tail part type M6. Brush material is Nylon.It can be used for HVAC condenser/chiller tube cleaning, high temperature steam or surface condensers tube washig and cleaning, firetube boiler tube washing cleaning and clean water tube boiler tube …The M6 connector can be male type or female type.

Usual size:Brush OD 10mm,12mm,14mm,16mm,18mm,20mm,22mm,25mm,30mm.
Also accept the customized size.

原産地: China , Sell to worldwide.

 Order Or Inquiry On “Chiller tube cleaning brush or Flexible connecting rod”

 

Models and Details for “Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner "

Chiller-tube-cleaning-brush

The connector is M6, usual type is male. But if you require, female connector can also be made.

condenser tube cleaning brush

You also can buy the following flexible connecting shaft:

Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner 1Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner 3Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner 5Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner 7

Flexible shaft: long 100cm,all are M6. Middle is nylon,flexibe.Quick-connecttion end,and threaded shafts and brushes.high performance nylon covered shaft allows deep cleaning of smooth bore chiller and heat exchanger tubes, leaving them debris free and with dramatically higher heat exchange efficiency.

 購入方法"Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner"

  • The item  is available for retail and wholesale;
  • 原産地は中国で購入した場合は、ご検討ください貨物(航空-海上のコスト
  • 受け入れ量コンテナを配置できる
  • ご連絡ください online (click here) Or send inquiry message to our email:  [email protected]

Maybe you are also interested:

Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner 9

General Knowledge on “Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner"

Scaling is plagued refrigeration industry is a major problem. Especially various types of heat exchangers, such as: metal pipe evaporator, condenser, absorber and heat exchanger fouling generation will prevent proper system operation, lower heat transfer coefficient, causing rust and partial wall corrosion, heat transfer coefficient due to reduced electricity consumption increased refrigeration equipment, increase energy absorption refrigeration, if cleaned once a heat exchanger, the heat transfer coefficient will increase the savings of 8% -16% of the energy.Use this “Chiller tube cleaning nylon brush,Spiral tube brush for condenser heat exchanger tube cleaner”,and its cleaning equipment,can remove the scale.

Rod and Brush Method
The oldest and least pleasant of chiller tube cleaners is the rod and brush method. This involves using a length of rod, usually metal of some sort, with a nylon, or wire brush larger than the tube inside diameter, attached to one end. Typically, the tubes are flushed with water from a hose, then the brush is manually pushed through the tubes. The tubes are then flushed again with water.

Advantages:

  • Low-cost
  • Simple operation – requires little training, or expertise

One Inquiry to Chiller tube cleaning brush and rod,Spiral tube brush for condenser heat exchanger tube cleaner

お電話でのお問い合わせ窓口のメッセージ

Your email address will not be published,just for us to contact you privately. * が付いている欄は必須項目です