Sale!

Injection packer for concrete crack repair

$0.01

Category:

Injection packer for concrete crack repair

Item:Injection packer for concrete crack repair

Short Description: Injection packer for concrete crack repair,Aluminum Grouting Injection Packer,Injection Packer , Epoxy Injection Packer , Plastic Surface Packer , Resin Injection Packer,Injection packer for concrete crack repair.It  is a kind of high pressure grouting machine accessoriesthe.It use the principle of loop pressure fastening. The head of packer is supplied with a single-way valve,which can prevent the slurry at high pressure into the pour spout.It usually filler necks used as connection pieces between the injection device and the building component. when sealing building structures or repairing cracks in the framework of crack injections. Zerk or button head fittings located on the top of the injection packer form the connection to the injection device. Depending on the type of connection to the building component, we distinguish drill-hole packers and surface packers. All packers are standard-equipped with high-pressure fittings. They are also available with low-pressure fittings upon request.

Size/Dimension:9.7x85mm,9.7x100mm,12.7x100mm,12.7x150mm,12.7x200mm,12.7x250mm,12.7x300mm

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Injection packer for concrete crack repair
Models & Details for “Injection packer for concrete crack repair”

High pressure injection packer for concrete crack repair

injection2a

injection5 injection6 injection7

Injection packer for concrete crack repair injection3 Injection packer for concrete crack repair

*Note:We can produce at any sizes Injection packer for concrete crack repair according to your requirements.

Smartclima manufacture and export high quality injection packer for concrete crack repair

Application :

High pressure injection packer for concrete crack repair is the accessory to be , waterproof ,rehabilitation of concrete structures , basement leak sealing cracksealing etc.
You can use injection machine in concrete crack repair and water leaking stop. It suits for both polyurethane and epoxy injection.

High pressure injection packer for concrete crack repairing is a kind of high pressure grouting machine accessoriesthe.It use the principle of loop pressure fastening. The head of packer is supplied with a single-way valve,which can prevent the slurry at high pressure into the pour spout.

Injection packer for concrete crack repair is a kind of high pressure grouting machine accessories is usually to applicate in the following  situation:
1. Roof concrete slab cracks, wall pipe, wall, water leakage, water blocking.

2. Subway, tunnels, culverts, sewage treatment pond, the water leakage cracks in concrete, with water blocking.
3.Concrete structure, beam, column, slab cracks, high pressure injecting epoxy resin.

4.Basements, underground garage, underground passage, the water leakage cracks in concrete, with water blocking.

Buying guide to “Injection packer for concrete crack repair ”
  • The item  is available for retail and wholesale;
  • The place of origin is in China,when you buy one or two,please consider freight(by air or by sea) into the cost;
  • Accept bulk order with Container delivery;
  • Please contact us to email: sale@smartclima.com
How to repair concrete crack with “Injection packer”

How  to repair concrete crack with Injection packer for concrete crack repair?

1.Crack and leakage condition inspection
Check the process procedure after finding the thickness, width and depth of crack and leakage condition of the structure

injection_01

2.Drilling Operation
Drill directly into crack section if the thickness of concrete is thinner than 10cm. For the thickness of 10~50cm, drill it with 45 degree angle by keeping a distance of 1/5 of concrete thickness. Make sure it penetrates the crack section. If the thickness is over than 50cm, keep the distance of 20~30cm and drill it with 45 degree angle until it penetrates crack section. And keep drilling by maintaining the fixed interval. (5 holes per 1 meter. Drill it in zigzags)

injection_1

3.Cleaning the crack

injection_2

4.Injection packers installation
After clean the inside of drilled holes with compressor,then make sure that rubber sleeve of packer and cutting line of tightening nut should be put into the inside of concrete surface when installing. Tighten the packer completely by using the T-box. (Packer might be damaged if you tighten it too strongly)

injection_3

5.Surface seal crack

injection_4

5.Injection Operation,Polyurethane high-pressure injection
Inject the waterstopping material by using the high pressure device or grease gun.  Maintain the initial injection pressure as around 40kg/cm and increase the pressure by each 10kg/cm gradually until the waterstopping material flows out from crack section. Water will come out from the crack section first and then waterstopping foaming agent and then water stopping liquid at last. If the waterstopping material that is not foamed comes from the crack section, then move to next packer for injection.

injection_5

6.Packer Removing Operation
Remove and break the packer by using vise pliers or hammer as a tool. If there is still a wet section, then inject the water stopping material again.

injection_6

7.Finishing Operation
Remove the water stopping material that is remained on the crack section. Spreading with the elastic sealing material.

injection_7

Enquiry or Reviews

5 Star

0 %
0 review(s)

4 Star

0 %
0 review(s)

3 Star

0 %
0 review(s)

2 Star

0 %
0 review(s)

1 Star

0 %
0 review(s)

0 Star

100 %
2 review(s)

Reviewed by 02 customer(s)

  • JOSE ANGEL

    Hello, I am interested in injection packers (9,7×85 and 9,7×100). Please, send me specifications (price, packing and shipping to Spain). Thank you.

    2015-05-14
  • Robin

    Hi Friend,

    I got your details from internet. We are traders from Dubai mainly dealing with crack proofing accessories, plastering tools, epoxy tools etc.

    I am interested in injection packers. Please sent me the pictures of 13mx 75mm, 100mm , 115mm etc. I prefer quality rubber with blue colour.

    Awaiting your earliest response.

    2014-03-30

Write enquiry message or review

Rate Your Satisfaction*