Digital thermostat controller wall mounted type model XH-W2111

You are locating here ⇓

You are here: Smartclima Home>>Electronic Function And Controlling Module Unit>>Temperature And Humidity Controlling Module Unit >> Wall Mounted Type Thermostat>>Digital thermostat controller wall mounted type model XH-W2111:

Item: Digital thermostat controller wall mounted type model XH-W2111

Description: Digital thermostat controller wall mounted type
Model:XH-W2111
Temperature range: -50-110 ℃
Thermostat Accuracy: 0.1℃
Temperature measurement accuracy: 0.1 ℃;
Input Power: AC85V-240V;
Output:1500-2200W
Sensor head: NTC;
Size: 138 * 98*446mm
Option:Red digital 1500w,Blue digital 1500w,Red digital 2200w,Blue digital 2200w,

Place of origin: China factory sell directly , Sell to worldwide.

Instructions
1, after power on,the thermostat power panel show as real-time temperature.
2, press the set button to display F1, then press the SET button to enter the F1 parameter setting.

Example I:
Requires heating mode
Heated to 50℃ to stop, 45℃ and then re-start
1 Set the stop temperature F1 = 50
2 Set the operating mode F2 = H to heat
3 Set hysteresis = 5
Set OK

Example II:
Requires cooling mode
Cool down to 25℃ to stop, 40℃ and then re-start
1 Set stop temperature F1 = 25
2 Setting the operating mode F2 = C Cooling
3 Set hysteresis = 15
Set OK

Parameter Operating Instructions:

F1: (stop temperature) Set the value of F1 to be as stop temperature, stop the output when the temperature reaches this temperature value;
F2: (mode setting) set to work in the heating or cooling state, the control process from low to high is heating mode, need to be set to H; the control process from high to low is cooling mode, need to be set to C.
F3: (hysteresis setting) To set the interval value, that is, after the arrival of the F1 value, the difference will be restarted. For example,If F1 is set to 50, F2 is set to H, F3 is set to 3, after heated to 50℃, stop,and then lower than the F1 value (3) that is 47℃ to re-start again.
F4: (temperature correction) for temperature error correction, real-time temperature value = pre-correction temperature + correction value.For example, If the previous temperature is 25, F4 is 0.3 then the value of 25.3
F5: (delay start) especially for compressor options ,for protecting the compressor from frequent start.
F6: (high temperature alarm) set this value, when the temperature ≥ this temperature, the screen flashes, the buzzer alarm
F7: (low temperature alarm) set this value, when the temperature ≤ this temperature, the screen flashes, the buzzer alarm

Q:Does the data can be saved after power off for this thermostat ?
A: OUR all thermostat with power-down memory, a set of life-long preservation, the next boot do not have to re-set
Q: Can this only control the heating? Can you control the cooling?
A: This section supports heating and cooling two modes, can enter the F2 choice, this is very important
Q: Can this probe be able to measure air? Can I measure water? Moisture? Do I need to buy a special probe?
A: Anything that comes with the probe can be measured, including water and air. There is no need to buy a dedicated probe, they just look different
Q: Can this set the start temperature and stop the temperature?
A: This is a high-precision thermostat, it has its set the way to stop the temperature for the value of Fl, fall back to the value of F3 to start again with the set start and stop is actually the same
Q: How long can this be used?
A: You can work 24 hours a year, the theory life can work for 10 years.

• The Digital air humidity control controller is available for retail and wholesale;
• Accept customized bulk production,putting your logo;
• The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
• Accept bulk order with Container delivery;
• Please contact us to email: hvac@smartclima.com ,we can supply a favourite item you need.

You are locating here: