Digital Temperature controller embedded thermostat model XH-W2060

You are locating here ⇓

You are here: Smartclima Home>>Electronic Function And Controlling Module Unit>>Temperature And Humidity Controlling Module Unit >> Embeded Type Thermostat>>Digital Temperature controller embedded thermostat model XH-W2060

Item: Digital Temperature controller embedded thermostat model XH-W2060

Place of origin: China factory sell directly , Sell to worldwide.

P0 temperature control mode
C: Cooling mode ；H: Heating mode；

P1 hysteresis setting
For example: P1 = 5
Cooling mode: When the detection temperature reaches the stop temperature, the relay is
disconnected, the cooling is stopped, the temperature rises 50C, the relay is closed again
Heating mode: When the detection temperature reaches the stop temperature, the relay is
disconnected, the heating is stopped, the temperature drops 50C, the relay is closed again

P2 temperature correction.
If the detection temperature and the actual temperature deviation, you can use this function
correction, the actual value = measured value + correction value, for example, measured the
temperature of 25 degrees and actually 26 degrees, can be set to 1 P2, then the final The
temperature is 25 + 1 = 26

P3 delay start.
This function is used for compressor cooling. If you purchase this thermostat for the
refrigerator freezer, then this value must be set, depending on the compressor’s back pressure
size, – the set value is 3-65 minutes, if you are not control Compressor or do not need to
delay the function directly skip this;

P4 high temperature alarm
Set the high temperature alarm value, when the detection temperature exceeds this value, the
screen flashes, the buzzer issued by the public;

Example of heating:
Control the heating rod to heat up to 45 ° C Stop,and when the temperature down to 30 ° C,
Reheat heating again.

Step 1: long-time press the SET key to enter the code menu, set the work mode to be H0.
Step 2: Set the stop temperature to 45 ° C, press the up button briefly, then press the set
button briefly again, stop temperature number flash, press the up and down keys to set the
value to be 45, press the Enter key to return.
Step 3: first press the down button, and then short press the SET button, hysteresis value
flash, press the up and down keys to change the value to 15.

Example of cooling use:
Control the cooling fan cooling to 26 ℃ to stop, the and when temperature rise to 30 ℃ to
cooling again;

Step 1: Press and hold the key to enter the code menu and change the P0 mode to C.
Step 2: Set the stop temperature to 26 ° C, press the up button briefly, then short press the
set button, stop the temperature digital flashing, through the up and down keys to set the
value to 26, press the Enter key to return.
Step 3: first short-press the down button, and then short-press the set button, the hysteresis
value flash, press the up and down keys to change the value to 4.

Fault code:

Displaying LL, means sensor problem, repair or replace it.

Displaying HH, means the temperature is over testing range.

How to set stop temperature?
way 1:
Press the set button, stop the temperature digital flash, through the up and down keys to set
the required value;

way 2:
Press the up button, press the set button, stop the temperature digital flashing, through the
up and down keys to set the required value;

way 3:
Long press the up button for 3 seconds to stop the temperature digital flashing, through the
up and down keys to set the desired value;

How to do hysteresis setting?
way 1:
Press the down button for 3 seconds, the hysteresis value flashes, through the up and down
keys to set the required hysteresis;

way 2:
Press the down button, press the set button again, the hysteresis value flashes, through the
up and down keys to set the required hysteresis;

way 3:
Long-time press the set button for 3 seconds, enter the internal settings, select P1, press
the set button. Enter the P1 set the state, recite the upper and lower keys to set the
required hysteresis;

How to power on/off?
Press-time press the switch key for 3 seconds for power off, then the thermostat will be in
the off state, the status indicator flashes, the output indicator does not light, then press
the switch button again to switch on.

How to restore the factory setting?
Long-time press the key of up and down button for 3 seconds, digital display 88, and then jump
to display the detection temperature, that is, to restore the factory settings.

• The Digital  temperature controller is available for retail and wholesale;
• The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
• Accept bulk order with Container delivery;
• Please contact us to email: econtrol@smartclima.com ,we can supply a favourite item you need.

You are locating here:

You are here: Smartclima Home>>Electronic Function And Controlling Module Unit>>Temperature And Humidity Controlling Module Unit >> Embeded Type Thermostat>>Digital Temperature controller embedded thermostat model XH-W2060