DC 12V Digital Thermostat Temperature Controller Model XH-W2020

You are locating here ⇓

You are here: Smartclima Home>>Electronic Function And Controlling Module Unit>>Temperature And Humidity Controlling Module Unit >> Embeded Type Thermostat>>DC 12V Digital Thermostat Temperature Controller Model XH-W2020

Item: DC 12V Digital Thermostat Temperature Controller Model XH-W2020

• Supply voltage:12V ;  Output voltage:12V
• Temperature control range: -55~120 ℃
• Resolution:0.1℃ (-9.9~99.9℃);other Temperature:1℃
• Temperature measurement accuracy:0.2%FS
• Control accuracy: 0.1 ℃
• Refresh rate:0.5s
• Thermostat probe: NTC 3950 / B = 10K 0.5%(waterproof type 1M)
• Output:directly output; Maximum capacity 10A
• Environmental Requirements: -30 ~ 60 ℃ Humidity 20% -85%
• Dimensions: 77 * 35 * 88mm
• Mounting holes dimension: 70*5*29mm

Place of origin: China factory sell directly , Sell to worldwide.

• Model:XH-W2020
• Supply voltage:12V
• Output voltage:12V
• Temperature control range: -55~120 ℃
• Resolution:0.1℃ (-9.9~99.9℃);other Temperature:1℃
• Temperature measurement accuracy:0.2%FS
• Control accuracy: 0.1 ℃
• Refresh rate:0.5s
• Thermostat probe: NTC 3950 / B = 10K 0.5%(waterproof type 1M)
• Output:directly output; Maximum capacity 10A
• Environmental Requirements: -30 ~ 60 ℃ Humidity 20% -85%
• Dimensions: 77 * 35 * 88mm
• Mounting holes dimension: 70*5*29mm

Instruction manual:

Code		Code Description	Setting Range	Factory settings
P0		Cooling/Heating	C/H	C
P1		Hysteresis setting	0.1-50	2
P2		Max setting value	120	120
P3		Min setting value	-55	-55
P4		Temperature correction	-10.0~10.0℃	0
P5		Delay start time	0-10 minutes	0
P6		High temperature alarm	-55~120℃	Off
P7	Data lock switch		On/off		Off
P8	Restore factory settings		On/off		Off

P0:Cooling/Heating mode

High temperature start cooling mode:C

low temperature start heating mode:H

P1:Hysteresis setting

heating mode(H):measured value<=set value – hysteresis start output heated to set value to stop

cooling mode(C):measured value>=set value – hysteresis start output cooled to set value to stop

P2:Max setting value

the setting maximum temperature does not exceed this value

P3:Min setting value

the setting minimum temperature does not lower than this value

P4:Temperature correction

When measuring the temperature and the standard deviation of temperature, you can use this function to correct.Corrected temperature = Temperature before correction + Correction value

P5:Delay start time (minute)

P6:High temperature alarm

When the measured temperature exceed this value,the screen will flash and send out warning beeps,at the same time forced turn off output.

P7:Data lock switch

Turn on the data lock switch,can keep the current setting is not altered.If you need to alter,please turn off the data lock switch.

P8:Restore factory settings

Long press SET button to swith P8,and press SET button again,set to on,then press RST button to restore factory settings.

• The Digital  temperature controller is available for retail and wholesale;
• The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
• Accept bulk order with Container delivery;
• Please contact us to email: econtrol@smartclima.com ,we can supply a favourite item you need.

You are locating here:

You are here: Smartclima Home>>Electronic Function And Controlling Module Unit>>Temperature And Humidity Controlling Module Unit >> Embeded Type Thermostat>>DC 12V Digital Thermostat Temperature Controller Model XH-W2020