Condenser tube brush and extension rods for cleaning chiller heat exchanger tube
Sell Condenser tube brush and extension rods for cleaning chiller heat exchanger tube,supplied by China manufacturer.Brush material can be Nylon,Brass or Stainless steel.Work with condenser tube brush extension rods,can clean HVAC condenser chiller tube, evaporator tube,high temperature steam or surface condensers tube washig and cleaning, firetube boiler tube washing cleaning and clean water tube boiler tube,and other heat exchanger`s tube …Keep your chiller and heat exchanger running smoothly with our durable condenser tube cleaning brush and rod.
Type:Nylon condenser tube cleaning brush,brass condenser tube cleaning brush and stainless steel condenser tube cleaning brush
Size:For cleaning tube 1/4″,3/8″,1/2″,5/8″,3/4″,1″,etc…Pls check below.
Place of origin: China , Sell to worldwide
Send Enquiry Message |
The “condenser tube brush and extension rods for cleaning chiller heat exchanger tube” is essential tool for cleaning the tubes of chillers,condensers and heat exchangers. The brush is made of durable, high-quality materials which can be nylon,brass and stainless steel and can effectively remove debris and build-up from the inside of the tubes. The nylon rod is flexible and can be connected together, making it suitable for use in a variety of applications. This tool kit is easy by manual to use and can help improve the efficiency and lifespan of your chiller or heat exchanger.See below models:
The condenser tube brush has three materialsas:nylon,brass and stainless steel. and rod is a tool kit used to clean copper tubes in heat exchangers and chillers. It includes a flexible rod with a brush for easily and efficiently cleaning copper tubes in heat exchangers,condenser,evaporator and chillers.The sizes we can supply are as following: (6mm and 8mm are also available.)
Models and Details for “Condenser tube brush and extension rods for cleaning chiller heat exchanger tube” |
Our condenser tube brush has three materials as below,and extension rod has two materials:
Nylon condenser tube brush |
We can supply Nylon condenser tube brush,the diameter can be: 6mm,10mm,12mm,14mm,16mm,19mm,20mm,22mm,25mm,30mm,40mm;
The cleaning brush 6mm with M4 male thread;
The cleaning brush from 8mm to 40mm,they are M6 male thread.
Brass condenser tube brush |
The following are brass condenser tube brush ,their bristles are made from brass,male thread M6,
For cleaning tube diameter:8mm,10mm,12mm,14mm,15mm,16mm,19mm,20mm,25mm,30mm,40mm;
Total length is 160mm, and the length of part of bristle is 110mm,thread type is male thread M6.Brass bristle diameter is 0.15mm
Stainless steel condenser tube brush |
The following is stainless steel condenser tube brush:
The material of brush bristle is grade 304 stainless steel, the bristles are dense to remove dirty more easily; the frame of the thickened brush rod is reinforced, durable and not easy to lose bristle, quality is assured.Non-standard size can be customized!
The bristle part is about long 100mm, the total length is about 165mm, with M6 male thread.
Brush diameter: 10mm, 11mm,12mm,14mm,15mm,16mm,18mm,20mm, 22mm,25mm,28mm,30mm,32mm,35mm,38mm,40mm, 45mm,50mm,55mm,58mm,60mm,63mm,65mm,70mm, 75mm,80mm,85mm,90mm,100mm. (Accept customized size)
Nylon extension rods for connecting condenser tube brush |
You can buy the following flexible nylon rod as connecting shaft to connect tube brush.
Nylon rod shaft is flexible,their specification is: long 100cm,diameter is 6mm and 8mm (defaulted diameter 8mm),both ends are M6 threads (one end is male M6 thread,and the other end is famale thread M6). The pieces can be connected together to get longer rod. The end with female thread can connect to the brushes above( Nylon condenser tube cleaning brush,brass condenser tube cleaning brush and stainless steel condenser tube cleaning brush).
High performance nylon covered shaft allows deep cleaning of smooth bore chiller,condenser and heat exchanger tubes, leaving them debris free and with dramatically higher heat exchange efficiency.
Notice: there are two diameters as below:
Nyloy rod 8mm suits for connecting brush from 10mm to 40mm.
Nyloy rod 6mm suits for connecting brush from 8mm to 40mm.
.
Handle for tube brush and extension rod: |
The following parts is used as handle for brush or rod. Female thread M6.
Stainless steel extension rods for connecting condenser tube brush |
The following extension rods are made from stainless steel 304,they can be connected together to get longer rods.
- The below one is for connecting “nylon brush 6mm” only. Long 1000mm, diameter 6mm,thread is M4.
- The below one is for connecting brush from 8mm to 100mm.Length can be 400mm, 500mm,and 1000mm per piece.Diameter 8mm,thread is M6.
Mini condenser tube cleaning brush&rod kit,Brush size 4.5mm,4.5mm,6.35mm |
The following brushes and rods fit for 4.5mm,5.5mm and 6.35mm condenser tube cleaning.
Brush bristle material: brass and contton;
Rod material: aluminium;
How to purchase “Condenser tube brush and extension rods for cleaning chiller heat exchanger tube” |
- The brush and rod is available for retail and wholesale;
- The place of origin is in China,when you buy one or two,please consider freight(by air or by sea) into the cost;
- Accept bulk order with Container delivery;
- Please contact us online (click here) Or send inquiry message to our email: hvac@smartclima.com
How to clean chiller/condenser/evaporator tube with Condenser tube brush and extension rods? |
Cleaning the chiller/condenser/evaporator tube with a nylon brush and shaft rod is an effective and affordable way of removing dirt, debris, and scaled deposits from the tube. Not only will this help ensure your condenser tube is functioning as efficiently as possible, but it will also ensure the unit will run at peak performance for many years to come. Here are some simple steps to quickly and easily clean your condenser tube with a nylon brush and connecting rod.
Step 1) Turn off the power to the condenser unit. Before beginning, make sure to turn off the Powers Off switch located near your condenser unit to ensure your safety during the cleaning process.
Step 2) Unscrew the access panel. Most condenser units have an access panel located on the back of the unit which must be removed before you can clean the condenser tube. Take a screwdriver, loosen the screws, and take off the panel.
Step 3) Locate the condenser tube. After removing the access panel, locate the tube that runs through the condenser unit. This is usually found on the side of the condenser unit.
Step 4) Clean the condenser tube. Measure your size of condenser tube diameter and choose a suitable nylon brush,then screw the brush onto the brush extension rods which can be connected together to prolong. Use water to flush the inside of tube and finally use the nylon kit to scrub the inside of the condenser tube to remove continue all dirt, debris, and scale deposits on the tube by doing come-and-back action.Make sure to reach the other end of the tube to ensure you get it completely clean.
Step 5) Check the condenser tube for any signs of damage. After completing the cleaning process, make sure to check the condenser tube for any signs of damage, cracks, or holes. If any of these are present, make sure to replace the tube as soon as possible.
Step 6) Replace the access panel, turn the power back on. Once finished with the cleaning process, replace the access panel on the condenser unit and turn the power back on.
By following these simple steps, you’ll be able to quickly and easily clean your condenser tube. Keep in mind, it’s important to regularly clean your condenser tube to ensure peak performance of your unit, and potential save you money on costly repairs.
General Knowledge on “Condenser tube brush and extension rods for cleaning chiller heat exchanger tube” |
Scaling is plagued refrigeration industry is a major problem. Especially various types of heat exchangers, such as: metal pipe evaporator, condenser, absorber and heat exchanger fouling generation will prevent proper system operation, lower heat transfer coefficient, causing rust and partial wall corrosion, heat transfer coefficient due to reduced electricity consumption increased refrigeration equipment, increase energy absorption refrigeration, if cleaned once a heat exchanger, the heat transfer coefficient will increase the savings of 8% -16% of the energy.Use this “Chiller tube cleaning nylon brush,Spiral tube brush for condenser heat exchanger tube cleaner”,and its cleaning equipment,can remove the scale.
The Chiller tube cleaning brush and rod is a tool used to clean copper tubes in heat exchangers and chillers. It includes a flexible steel rod with a brush at the end, which can be inserted into the tube to remove any debris or buildup. The brush is made of nylon or other durable materials that won’t damage the copper tube. This tool makes cleaning chiller tubes much easier and more efficient, ensuring that the equipment runs smoothly and efficiently.
Rod and Brush Method
The oldest and least pleasant of chiller tube cleaners is the rod and brush method. This involves using a length of rod, usually metal of some sort, with a nylon, or wire brush larger than the tube inside diameter, attached to one end. Typically, the tubes are flushed with water from a hose, then the brush is manually pushed through the tubes. The tubes are then flushed again with water.
Advantages of Condenser tube brush and extension rods:
- Low-cost
- Simple operation – requires little training, or expertise
Related Products:
Enquiry or Reviews
5
/5Based on 09 rating(s)
5 Star
4 Star
3 Star
2 Star
1 Star
0 Star
Reviewed by 10 customer(s)
Mangal Singh
Respected Sir Ma’am
We want buy Nylon Brushes 8MM., 10MM., 18MM., 20MM. size brushes and we want to purchase 100 pecs of brushes every size mention by us2023-07-12ReplyDaniel pulfer
Hi how much is the 6,8 and 10 mm brush with a rod please
2023-07-09ReplyBoban
I need nylon brush for cleaning chiller tube
2023-06-15ReplyBoban joseph
How can order chiller tube cleaning brush, size 8mm and 10mm size, each 10 pcs
2023-06-15ReplyBradley McCOnnell
Price on chiller tube cleaning brushes and rods for delivery to Australia
2023-06-14ReplyPatrick
Good morning,
I’d like a quotation and lead time for:
10 blue nylon brushes 10mm
10 blue nylon brushes 12mm
flexible rods (4 x 1m)Delivery would be in Florida
Thank you,
Patrick
2023-05-18ReplyMalvein
I am looking for a condenser brush with rod
2023-05-09ReplyRajat Singh
How many price boiler cleaning round nylon brush 8mm, 12mm, 16mm 26mm
2023-04-26ReplySuresh Shetty
Need Parts Number for brush and rod,spiral tube brush for heat exchanger tube clearing.
Please send all detalies with prize with parts number.2022-12-01ReplyKaushik I Prajapati
We are required og Niylon Blue
, stainless brush2021-12-07ReplyTushar Namjoshi
NEED CHILLER TUBE CLEANING BRUSH AND ROD,SPIRAL TUBE BRUSH FOR CONDENSER HEAT EXCHANGER TUBE
2021-09-16Reply
Write enquiry message or review