smartclima logo

Christopher, Author At Smartclima

Author: Christopher

MCQUAY Air Conditioner Fault Code

Fault display: (only applies to SLM APM01C controller) failure code fault
E0 E1 controller system fault an external fault input (current overload of the compressor) E2 External fault input (low voltage protection compressor system) E3 External fault input (compressor and high pressure protection) return air temperature sensor in E4 E5 indoor coil sensor missing or off or short circuit short circuit outdoor coil sensor off E6 E7 E8 outdoor ambient sensor to fall off or short circuit or short circuit the refrigerant leakage E9 coil temperature Overrun of more than 68 EA pump failure or water level cooling water temperature too high or too low EB EC network communication failure for McQuay modular air cooled water chiller/heat pump unit MAC210//DM/DR/DRS/DR MC302l controller user’s manual, operation
1, switch machine
Press the on/off key, unit powered on (RUN led lit), shutdown (RUN the lights) to switch between.
2, mode selection
Press the “mode” button to switch between cooling/heating mode, it should be noted that is, models but must be performed in a shutdown state.
3, parameter queries
Use the controller to query the network of any unit of work status and parameters (which compressors work, set the water temperature, water temperature, water set temperature, water temperature, timing settings of the unit, refrigeration and freezing temperatures, freezing temperatures, defrosting temperatures in winter).
By “unit” key Hou unit number flashing, at by “▲” or “” key change unit,, check see of is different unit of current parameter, to query a unit of work parameter, found to query of unit, Shi by “determine” key can query the unit of work parameter has, by “▲” or “” key view the unit of different of parameter.
4, parameter setting
① Press the “password” button in the left box under monitor display “password” and “00”, press “▲” or “” key to adjust the value when you select into the correct user password and press “OK” button (factory code to “00”), display box display time, it means that you’ve entered the correct password, you can make the following settings:
A, parameters change: after you enter the correct password, follow the steps ②→③→④ can complete the operation parameters of the modify settings.
B, the user password changes: after the correct password is entered, press the “password” button to display a box only displays “00”, then enter the user password to modify setting, press “▲” or “” key to adjust the value, press the “OK” button modifications support password to complete, and jump out of the parameter set state.
II press the “set” key unit number flashes, then press “▲” or “” key to adjust the unit, find for setting parameters of the unit, press the “OK” button you can set the unit’s operating parameters (parameters that can be set are: cooling water temperature, the heating water temperature).
③ Press “▲” or “” key to select the parameter you want to set, press the “OK” button you can press “▲” or “” key to set parameter values, after Setup is complete, press “OK” key to save the setting result.
④ Repeat step ② additional parameters that can be set (Note: not available within 60 seconds press the key to exit the parameter setting).
⑤ set parameter values must be performed in a shutdown state.
5, real time clock settings
With needle shaped tool by “mode” key above of small hole, LCD display Shang displayed “week set” of words, by “▲” or “” key set current time is week several, set good has zhihou again by small hole, week set success, while display Shang displayed “clock set” time will flashing, at by “▲” key modified hours, by “” key modified minutes, again by small hole can save set of clock.
6, regular set
① Press the “timer” button on the monitor at the same time show “week setting” and “timings” message, press “▲” or “” key to select a time in the week to set the timer, select, and then press “OK” button appears on the display “timer set” message, selected scheduled weeks, into the scheduled times.
II into timing frequency setting, press “▲” or “” key to select which day to set timing (can be set to 4 in the “unit” above), press “OK” key to select a time, into the timer on or off option.
③ Press “▲” or “” button to select “timer on” and “time off”, press “OK” key to select the timing is either on or off, enter timing selection, at this time appears on the display “timer set” and “clock set” and the time flashes.
Black press “▲” keys to change the hour, press the “” key, modify the minutes set time and press “OK” button to complete the timing of all the settings and save the settings, at this time appears on the display “timer set” and skip to step three parts, clock times and regularly order last week, cycle settings timed for a week until the exit time set.
⑤ If you want to cancel a timer, this timing timing must be set to 00:00. If you want to cancel all the time, you also need to press the “mode” and “set” keys, “dropping—–” after the sound of a Bell, all clear and timing.
Note: the regular boot and timed shutdown was subject to the clock time on the wire, if the clock is not accurate, regular boot and timed shutdown time will not be allowed. Scheduled during the Setup process, press the “unit”, “mode”, “password” key or 5 seconds no button will exit the timer settings (does not save the setting). Factory default timer as the 00:00.
7, manual defrost
Unit when the heat press “▲” or “” keys until the “manual defrosting” appears press “OK” key, enter manually defrost status. Exit the defrosting condition: ① the defrost time is more than 10 minutes; or II if the defrosting temperature defrost probe detects a temperature greater than setting temperature and defrost time heavy rain for 1 minutes.
8, reset
Press with a needle tool press the “▲” button at the top of the small reset hole.

Fault Code

 Code Possible Fault Code  Possible Fault
 EC00Number 15 sub-machine communication fault ER30Present machine group fault
 EC** **Number 1-14 sub-machine communication fault ER31Machine communication fault
 EC15 Number 15 sub-machine communication fault ER40 TH1 fault
 ER16 Copressore overload ER41 TH2 fault
 ER17 Fan overload ER42 TH3 fault
 ER18 Pump overload ER43 TH4 fault
 ER19 Less water flow ER44 TH5 fault
 ER20 High pressure fault ER45 TH6 fault
 ER21Low pressure fault ER46 TH7 fault
 ER23System fault ER47 TH8 fault
 ER25Low temperature of outlet water ER48 TH9 fault
 ER26Heating overload ER49 TH10 fault
 ER27 Circumstance temperature high/low ER50 TH11 fault
 ER28 Star urgent working function ER51 TH12 fault
 ER29 Overheat less than  1 degreeprotection ER53 Low pressure sensor fault


MACD module can store 16 a history fault, can through main module Shang of “K1” “K2” “K3” “K4” four a press find, specific method following: continuous by “K1” key until digital tube displayed “OHE”, then by “K4” key confirmed, displayed “HE–“, again by “K4” displayed “HE0-“, said need check subsection several fault, can through “K2” and “K3” press Shang turned or Xia turned, find subsection several fault, then by “K4” confirmed,  NIXIE tube displays the fault code. Example 1: display “HE0-“, after “K2” until “HE01”, press the “K4” by highlighting “ER21”, said the second failed for low-voltage fault.
Example 2: the need to find the 12th failure
Show “HE–“, after “K2” shows “HE-1”, and then press the “K4” by highlighting “HE1-“, and then press the “K2” until the digital display “HE11”, and then press the “K4” fault code confirmation can be found in the 12th. Troubleshooting “HE00” to “HE15”, represents the 16th the fault number. If you find fault display “ER00” indicates that the fault number fault-free. Such as found in “HE02” failure “ER00”, which means no third behind and fault injection: keys must be within 5 seconds operating MDS digital variable capacity multi-connected air conditioning system trouble codes
Cause codes E0 outdoor unit exhaust temperature temperature fault E1 DLT outdoor units OD ambient temperature temperature sensor outdoor machine fault E2 RTN temperature temperature sensor fault E3 E4 outdoor temperature temperature sensor fault at the bottom of the compressor Inlet temperature temperature sensor Midlet temperature temperature fault fault E5 outdoor machine E6 E7 outdoor outdoor Outlet temperature temperature sensor fault DLT exhaust temperatures Through the high conflict E9 E8 fault EE mode indoor unit fault F1 pump room ambient temperature sensor failure

A light commercial compressors

EMBRACO China factory recently started producing compressors developed for commercial refrigeration products, the first product designed for commercial freezers and stereo display cabinet design, called EMT series compressors.

It is reported that EMT EM production series compressors. Responsible for EMBRACO commercial refrigeration products marketing Andr é Holderbaum said: “through EMT EM production series compressors are efficient, small size and low noise characteristics, also compatible with R134a R290 refrigerant. ”

Holderbaum said that in recent years, Chinese exports of commercial refrigeration products is on the rise, EMBRACO was concerned. He said: “commercial refrigeration compressor products locally in China are put into operation, we will enhance the level of service, making our service more flexible, while monitoring the trends of the market. ”

Brushless DC motor for air conditioning in Wolong reached advanced level of similar products

A few days ago, from Wolong electric group control Office was informed that the new product development, the company developed plastic-sealed brushless DC motor for air conditioning has successfully entered the production phase. Proven, new efficiency, noise, vibration and other performance parameters have reached the advanced level of similar foreign products.

It was also noted that, DC motor for air conditioning in Wolong is preparing for mass production, current DC motor production plant has been completed, the debugging work completed, is expected to formally put into production in late September 2009, initial design capacity of 100,000 units a month later according to the demand of the market due to enlarge. In addition, the Wolong DC motor test samples have been sent to major customers, feedback is more ideal.

Welling wash motor sales in the first half of this year grew by 15%

Has learned the first half of 2009, welling wash motor sold about 4.628 million, exports about 3.209 million units, overall sales last year rose by about 15%. Under the influence of changes in overall market demand, welling wash motor sales change in the structure of the first half of 2009, washing motor sales rose 89%, drum-type washing machine motor 14%. In order to ensure the washing Motors business development, Wellington and actively promote new products, the first half of 2009 into the food processing small series motor products industry, the successful development of motor and large volume sales of soy milk. But the impact as well as falling commodity prices product sales, welling wash motor a turnover of HK $ 687 million, down by 12%.

Ruizhi 2010 plans to produce 400,000 sets of compressor

Recently, ruizhi compressor got the news that the 2010 ruizhi inverter compressor is scheduled to produce 400,000, mostly in mainland China, a few from China’s Taiwan factory. City’s products are mainly for Japan and air conditioning in city markets.

XI An Qingan: 2009 Annual compressor frozen sales of 1.314 million units

Has learned the 2009 frozen year Xian Qing an air conditioning compressor 1.314 million set. In addition, XI An Qingan achieved new progress in developing energy efficient products, a new series high-efficiency products have matches completed, starting from September 2009 bulk supply.

Sichuan Changhong high efficiency air conditioner compressor production

Recently learned that, Sichuan Changhong has begun mass production of energy-efficient air conditioning compressors. According to CHANGHONG in charge, this new models now account for CHANGHONG 30% of the purchase, the future is expected to reach 70%.

Ling Da compressor full production

Recently, gree owned Landa compressor was informed that in August 2009, the company has been producing at full capacity in September, Ling Da compressor more demand. Now Ling Da has been reported to stop production energy efficiency class 3 compressor, all to produce more than 2 levels of energy efficiency products.

Danfoss financial crisis led to the first half of 2009 decreased performance

A few days ago, Danforth released its 2009 financial report in the first half. According to the report, the first half of 2009, Danfoss sales of 12.5 billion Denmark kroner (about 16.816 billion yuan), up 10%, excluding other income and expenses profit loss of 660 million, Denmark krone, first half of 2008, the figures for profit of 693 million Denmark Krone.

Danfoss expects net sales for the year to 24 billion to 25 billion Denmark kroner pretax profit forecast to-1.6 billion Denmark kroner to-1.9 billion Denmark kroner.

A few problems that you need to know in floor heating system

Floor heating has a few problems that need attention, you know? With the arrival of cold weather in winter, many people are going to choose to install floor heating, have a warm room in their home environment. Heating a system, covers all aspects of the problem.

1. Select the heating pipe problems: select will directly affect the life of the floor heating system heating pipes, floor heating system is a system of long-term covert use, choose what kind of heating pipe directly affects the life of the whole system. When selecting a heating pipe can select imported pipe or joint-venture companies, no province during an initial installation cost, select the pipe too cheap at a later stage, maintenance costs or even in early times, and a construction boom. So choose good quality pipes, is the high cost is worth it.

2. Select water-divide problem: water-divide is the main material of the floor heating system, quality, directly related to the operation of the whole system, and may not match the corresponding temperature, causing budget overruns. In this regard, importing diversity has great advantages in quality and uneven domestic products, and applied for a short time, the quality varies greatly, so choose carefully, suggested the use of products from well-known manufacturers.

3. install floor heating engineering problem: accurate should be strictly in accordance with construction drawing design, due to warm is a system, when installed, must be good and home improvement, and must not be installed on the warm floor random construction work, has the potential to cause damage to the heater. And cannot be opened without permission to warm the device, if it will affect the construction, you must get in touch with installing floor heating supplier, in time.

4. There is no need to install temperature-controlled Central: some type of heating area is big, generally recommend installing temperature-controlled Central, so that each can be individually set the heating temperature of the room, or you can set the temperature of the room to a minimum, keep running. By temperature-controlled central control, significantly saving energy profligacy; and easier centralized management control.

Potential risk factors for solar polysilicon production process

Different from those used to electronics and solar cells, monocrystalline silicon, is also different from amorphous silicon thin-film devices and solar cells, polysilicon is made up of tiny silicon materials. Major polysilicon producer Hemlock Semiconductor, OCI, WACKER (Wacker Chemie), GCL-poly energy, and REC, LDK Solar, MEMC, and some smaller producers.

Polysilicon industry is developing rapidly, and levels above 1000t polysilicon production plant were built. However, polysilicon production process, hydrogen, chlorine, trichlorosilane and silicon and other harmful substances, and there are fire, explosion, poisoning, suffocation, electric shock injuries and many other risk factors.

Harmful substances produced in the polysilicon production process of chlorine gas, hydrogen, Silicon, hydrogen chloride, trichlorosilane, main risk characteristics are:

1. hydrogen gas: mix can form explosive mixtures with air, heat or open flame or explosion. Gas is lighter than air, when indoors use and storage, leakage increased stranded roof difficult to discharge, when Mars will cause an explosion. Halogens such as fluorine, chlorine, bromine and hydrogen will react violently.

2. oxygen, combustible materials, combustible matter combustion and explosion of one of the essential elements and oxidation of most active substances. And combustible (such as acetylene and methane) forms explosive mixtures.

3. chlorine: a pungent odor and can be generated with a number of chemical explosions or explosive material. Almost all metallic and non-metallic corrosion. Are highly toxic. Is a strong irritant gases.

4. hydrogen chloride: anhydrous hydrogen chloride is non corrosive, but when in contact with water, are corrosive. Can react with reactive metal powders, releasing hydrogen gas. Cyanide can produce highly toxic hydrogen cyanide gas.

5. three hydrogen Silicon chlorine: open flame burning strongly. Subject to high thermal decomposition may produce toxic chlorine gas. Reacts with oxidants, are a fire hazard. Very volatile and fumes in the air, in contact with water or water vapour can generate heat and toxic corrosive smoke. Combustion (decomposition) products: hydrogen chloride, silica.

6. Silicon tetrachloride: heating or hot water liberation, release toxic corrosive smoke.

7. hydrofluoric acid: corrosive, very strong. H vesicant immediately burned. Can react with bare metal and releases hydrogen with air to form an explosive mixture.

8. a nitric acid: strong oxidizing. And combustible (such as benzene) and organic matter (such as sugar, cellulose) exposure will react violently, even cause fire. With alkali metals react violently. Has strong corrosion resistance.

9. the nitrogen: in case of high fever, increased pressure within the container. Cracking and danger of explosion.

10. hydrogen fluoride: highly corrosive. In case of high fever, increased pressure within the container, is in danger of cracking and exploding.

11. sodium hydroxide solution: this product is non-combustible, with strong strong corrosive, irritant can cause the human body burns.

Second, electric shock, other risk factors such as mechanical damage

Fire, explosion, poisoning is polysilicon projects in major danger and harmful factors in production, in addition, there is electric shock, mechanical damage, corrosion, dust and other hazardous and harmful factors. Are:

1. preparation of hydrogen: electrolyzer, hydrogen, and oxygen tanks, fire and explosion, electric shock and mechanical damage.

2. hydrogen chloride synthesis: synthesis furnace of hydrogen chloride, chlorine and hydrogen gas buffer tanks, fire and explosion, poisoning, electrocution.

3. the three Silicon-hydrogen chloride synthesis: three Silicon-hydrogen chloride synthesis furnace, synthesis gas scrubbers, feeding machine, fire and explosion, electric shock, poisoning, corrosion, mechanical damage and dust.

4. the synthesis gas separation: mixed gas scrubber, hydrogen chloride absorption tower, Tower, the mixed gas compressor hydrogen chloride resolved, fire and explosion, electric shock, poisoning, corrosion, mechanical damage.

5. separation of chlorosilanes: distillation, reboiler, condenser air, fire and explosion, electric shock, poisoning, corrosion, mechanical damage.

6. the three hydrogen Silicon chlorine reduction: three hydrogen Silicon chlorine carburetor, reduction furnace, reduction furnace cooling water circulation pumps, fire and explosion, electric shock, poisoning, corrosion, mechanical damage.

7. restore gas separation: mixed gas scrubber, gas compressors, hydrogen chloride absorption towers, fire and explosion, electric shock, poisoning, corrosion, mechanical damage.

8. hydrogen-Silicon tetrachloride: Silicon tetrachloride carburetor, hydrogen furnace, fire and explosion, electric shock, poisoning, corrosion, mechanical damage.

Based on the above analysis, it is the main potential risks of fire and explosion, chemical poisoning, harmful factors in terms of technology, equipment, facilities and protection problems and defects, is very likely to occur, it should be for reasons that may occur and take preventive measures to actively exclude.

Primary prevention measures are: automatic control system for production use, and improve the standard of control; in chlorine, hydrogen chloride, trichlorosilane Silicon Silicon chloride, hydrochloric acid, easy to leak part of fresh air and sets flammable and toxic gas detection and alarm system; personnel issued qualified for the job for antivirus, dust-proof and burns and other protective equipment to avoid risks of polysilicon.

how to choose radiator

Warm radiator pros and cons about starting from the first House until now, is constantly learning, a little dizzy, the problem with this is the benevolent.

Just finished decoration and immediately renovated a House, through practice, comparison, I still want to try change: simple or primitive style last time and, more recently, of simple pastoral grasses begin to grow, my husband says I’m too fickle, and alas! Say say it right, maybe a couple of days and changed my mind about it?

Floor heating is much better than radiator. In fact, heating technology and materials is very mature and has decades of history in China, just about enough to know it will have to be worried. Floor heating does not occupy the indoor space relative to the radiator, more comfortable than radiator heating, heating customer will save money. As long as the heating of underground pipelines during construction is impossible to protect late may cause a problem, much more security than the radiator, the radiator’s interface is very easy to leak, and relative to the life of the radiator to warm to much shorter. To warm the fault rate is much smaller, and maintenance is simple.

So I think now is sure to open your eyes and select a trustworthy shop, doing well to warm! Maybe ten years after, renovation, demolition, think are terrible, renovation is tiring!27455

How much can energy-saving air conditioning save money

In an interview, the reporter found that while “China energy efficiency labeling” in conditioning prototype can be seen on the fuselage, but many salespeople explained or vague, or to my problems, and some are even alleged to have misled consumers.

Air conditioning in some counters, sales staff said the air conditioning in a level 4 grade 1 efficiency energy efficiency is equivalent to other brands, in fact here, the salesperson is constant-frequency air conditioning inverter air conditioner efficiency ratings and mixed with the energy efficiency levels of contrast, he means a level 4 of variable frequency air conditioning energy efficiency equivalent to level 1 of another fixed-frequency air conditioning energy efficiency.

In interviews, reporters also found a citizen is the selection of air conditioning was a little confused and asked: “energy efficiency standards for national unity, don’t you? why are 4 levels of energy efficiency, the air conditioning energy efficiency ratio is 3.4, but that air conditioning is just 2.8? what about this air conditioner can save much electricity?” At least once a month, 60~70du. “The sales staff said, pretty sure. “Can save so much? ‘ how was this data out?” ” Calculation method is complex and involves a lot of expertise, I don’t know specifically, but buying it must deal, put up energy efficiency labeling of a simulated? ” Ultimately, the customer is befuddled and left.

In the course of visits to, the reporter noted, some outside sales personnel, in addition to greater efficiency than the vague, is also alleged to have misled consumers. In another air conditioning counters, sales staff even told customers, just labeled as “China energy efficiency labeling” air conditioners are energy-saving products. In fact, air conditioner “energy label” consists of 1, 2, 3, 4, 55, only energy efficiency for level 1, level 2, products can be called energy-efficient products, like 5 levels represent energy-intensive products, market access indicators and, therefore, not “energy label” equate the and saving energy.

B simple formulas to help you count the air conditioning energy saving accounts

In fact, to count the air conditioning energy saving accounts, must first figure out air conditioner “energy efficiency ratio”, because it is a measure of an air conditioner is energy efficient or low energy-efficiency standards.

The so-called “energy efficiency ratio” is the ratio of air conditioning refrigeration and cooling power, in other words, is 1-kilowatt how many kilowatt of electricity generated by an air conditioner with a cooling capacity, for example a 2P air conditioner cooling capacity is 5000W, cooling power is 1785W, so its energy efficiency ratio is 5000/1785=2.8, EER, the greater, shows air conditioning energy efficiency rating, the higher energy the better.

At present, the State aiming at constant speed inverter air conditioner and air conditioning, and enactments of two corresponding to the energy efficiency standards, among them, the constant-speed air conditioner 1~5-level energy efficiency ratio was 3.4, 3.2, 3.0, 2.8, 2.6 and 5.2 per cent of variable frequency air conditioning, 4.5, 3.9, 3.4, 3.0.

Then, on a daily basis, high level energy efficiency ratio EER air conditioning is better than low level air conditioning how much electricity it? gree electric appliances sales co marketing Dragon Minister told reporters that settled this account, it’s really quite simple, or as a cooling capacity up to 5000W 2P air conditioning, for example:

Grade 1 efficiency of the electricity consumption of 5000W/3.4=1471W, namely, power consumption per hour 1.471

2 energy-efficient electricity consumption of 5000W/3.2=1563W, 1.563 per hour electricity

At current electricity charges 0.62 Yuan/degree calculation, if a family uses 4 months in a year (about 120 days), power on 8 hours a day, the grade 1 efficiency ratio 2-level energy efficiency can save a year for electricity: (1.563-1.471) x8x120x0.62=54.76 ().

Do you know the best temperature for air conditioner to save electicity?

Summer, the home of the meter just like mounting the motor, go fast, coupled with a rise in electricity prices, and energy conservation awareness is becoming more and more strong, air conditioning in some air conditioning consumers to figure out how to make the family’s electricity-saving, studying air conditioning not only open to a few degrees of electricity. Constant temperature air conditioning experts in Hunan told the secret of your air conditioning costs, hopes to use air conditioning at a later time more wisely.

The heat of the summer, usually turn on the air conditioning back home, transferred to the extreme low temperature, is also sweating on the outside, entered the House as it as if we were into the Icehouse, cool is cool, but this is likely to cause the common cold, but electricity has many. Watch air conditioning remote control, refrigeration can be up to 16 degrees Celsius, what should the thermostat to how many degrees do better? Tell you that air conditioning set at 26 degree Celsius is best and why?

This is because the impact on human health of comfort in addition to lighting, air conditioning, color perception, as well as temperature and humidity. Statistics showed that the best human comfort when the temperature is between 24~28℃. Another point, set the air conditioner at 26 ° c has an economic benefit. Taking the city of Changsha as an example, if an air conditioner temperature increases of 1.5 HP split air conditioner 1 c, 0.4 kWh of electricity savings from run for 6 hours a day, calculated according to 4 months in the summer, you can power-saving 48 degrees, is around 70, in fact, value is much greater than this value.

To sum up, household air conditioning up to 26 ° c is the most comfortable, most without electricity!

Stamping holes on metal sheet

Punch: refers to the steel plates, leather, cloth, wood and other materials play a variety of graphics to fit different needs.

Punch type: Cross, diamond-shaped hole, fish hole, eight-hole, hexagonal hole, punched-plate, long hole, square hole, round hole, punched-plate screen, triangle hole and so on.

Punched sheet metal type: stainless steel plate copper plate aluminum and so on.

Characteristics of hydraulic system for rolling mill

Are based on motor power of hydraulic system for rolling mill with a hydraulic pump mechanical energy into pressure to promote hydraulic oil. Change the hydraulic oil flow through control valves, thereby promoting hydraulic cylinders have a different tour, different directions of motion, the successful completion of various other equipment different action needed.
1, can be implemented in running a large range of stepless speed regulation.
2, under the same power output, hydraulic drive device of movement inertia is small, small volume, light weight, good dynamic performance.
3, the use of hydraulic transmission can achieve seamless transmission, smooth motion.
4, easy to realize the automatic work cycle and automatic overload protection.
5, because the oil is generally used as a transmission medium, so self-lubrication of hydraulic components and has a long service life.
Characteristics of rolling mill hydraulic system affects its use value, these bright spots to support it’s reliable, safe, effective operation.

Mitsubishi Electric centeral air conditioning

Are you still worried about heating problems in winter the Villa? Your villa also for gas rationing to fret about it? You are still higher for gas and oil heating costs and safety concerns to worry about it? Mitsubishi Electric “ice fire” central air-conditioning system to help you solve these problems! In order to meet the heating requirements in winter at high altitude and in the North, and Mitsubishi Motors in air conditioning systems introduce “gas-liquid enthalpy” loop of compressors, with Mitsubishi Electric patented technology, the new building-the “ice fire” of VRF air conditioning system, completely solve the problem of heating in winter.
With central heating, electric boiler, gas boiler compared to traditional heating mode, Mitsubishi Electric “ice fire” multi-connected air conditioning low operation cost, eliminate security risks, more environmentally friendly and energy saving. “Ice fire” multi-connected air conditioning system in the industry for the first time using a “gas-liquid enthalpy” loop of compressors, solved in the case of outdoor temperatures reduce heat attenuation of bigger problems, ensure that the whole system of air conditioning and heating seasons that would continue to operate efficiently.
Superior heating performance from the top product technologies:
1,Mitsubishi Electric use patents owned by “enthalpy of gas-liquid Jet” technology of the compressor, the compressor even in the very cold conditions can complete the refrigerant compression process, units under the outside temperature at-15 ° c, the heating capacity-no attenuation, high heat, thoroughly solve the problem of air-conditioning system in winter heating effect is not guaranteed.
2 HIC, Mitsubishi Electric patented technology application of heat exchange technology, makes the unit heat from the outdoor air capacity enhancement, perfectly in line with the “gas-liquid enthalpy” loop used refrigerant circulation increased unit heat faster start-up.
3, the whole original Japan import, with stepless DC inverter technology, extra long design life of 20 years.
Mitsubishi Electric CITY MULTI “ice fire” multiple-conditioning system to solve your worries, systems do not require daily maintenance, operation is very simple.
There are now more clients appreciate the excellent quality of Mitsubishi Electric central air conditioning.23516