logo

water-cooled heat exchanger,Hydraulic Oil Cooler OR series

HVAC Parts >>Refrigerating Parts & Heating Elements>>Heat Exchangers>> Water-cooled heat exchanger/Hydraulic Oil Cooler

water-cooled heat exchanger,Hydraulic Oil Cooler OR series

Item: Water-cooled heat exchanger/Hydraulic Oil Cooler,OR Series heat exchanger

Short Description: water-cooled heat exchanger,Hydraulic Oil Cooler OR series(oil to water or water to oil cooler) is a tube exchanger which copper tube is built in the tube.With outlet&Inlet. You can refer to the following charter for parameter.It is widly used as heat exchanger of water and oil.

Models: OR-60,OR-100,OR-150,OR-250,OR-350,OR-600,OR-800.OR-1200,etc…

Place of Origin: China , Sell to wordwide

Models & Details for “water-cooled heat exchanger,Hydraulic Oil Cooler OR series”

Product Features:

Two types of heat exchanger are used to cool hydraulic oil: (1) shell-and-tube and (2) finned tube. The shell-and-tube heat exchanger has a series of tubes inside a closed cylinder. The oil flows through the small tubes, and the fluid receiving the heat (typically water) flows around the small tubes. Routing of the oil can be done to produce a single pass (oil enters one end and exits the other end) or a double pass (oil enters one end, makes a u-turn at the other end, and travels back to exit at the same end it entered).

Above is typically a shell and tube-type heat exchanger. The cooling water is pumped into the heat exchanger and flows around the tube bank. The hydraulic fluid, which is to be cooled, flows through the tubes. While flowing through the tubes, the fluid gives away heat to the water, thereby reducing its temperature.

Advantages of  water-cooled heat exchanger are:

1. They are very compact and cost-effective

2. They do not make noise

3. They are good in dirty environments. 

water-cooled heat exchangerwater-cooled heat exchangerinside of OR heat exchanger

oil-cooler-or-series

Models: OR-60,OR-100,OR-150,OR-250,OR-350,OR-600,OR-800.OR-1200,etc…

Buying Guide to “water-cooled heat exchanger,Hydraulic Oil Cooler OR series”
  • The product is available for retail and wholesale;
  • The place of origin is in China,when you buy one or a small quantity,please consider international air freight as cost;
  • Accept bulk order with Container delivery;
  • Accept customized production;
  • More types of  water-cooled heat exchanger,Hydraulic Oil Cooler OR series are not displayed on the web.If the item above doesn`t meet your requirement,please contact us to email: sale@smartclima.com ,we can supply a favourite item you need.
General Knowledge on “water-cooled heat exchanger,Hydraulic Oil Cooler OR series”

Water-cooled heat exchanger,Hydraulic Oil Cooler OR series,is a tube fin heat exchanger.Composed by copper tube(inner tube) and iron shell.Has inlet and outlet for liquid.It is a high effience heat exchanger.It has good performance.

1. Good heat exchanging effience.It is multi-tube coolers,with large cooling area, has the best cooling effect.

2. The cooling area is full. Number of copper pipe used in this cooler is thress times than fin-tube rolling the tooth-shaped tube, tubular cooling area calculation according to the surface area, so the cooling area is full.

3. Optimum thermal cooling pipe material. Pure copper, thermal conductivity 0.95.
Caution:

1. The cooling pipe of the oil port only two entrances to decide freely, unrestricted flow of oil itself. While imports of water must be entered from the bottom, the top of the water outlet oil.

2. Food and chemicals must not be used.

3. Water inlet and oil inlet temperature difference can not be installed when used above 80 ℃.

4. Maximum pressure: oil side 10 kg / cm 2, water side 7㎏ /cm2


5 Comments  to  water-cooled heat exchanger,Hydraulic Oil Cooler OR series

  1. anthony good says:

    can you supply an exchanger to cool 100hp diesel engine fresh water with sea water
    connection pipe fittings are 1″ 1-3/4″ id
    thankyou

  2. Bill Parks says:

    Hello!I am interested in getting quotes for Water-Cooled Heat Exchanger OR-350 and the OR-600. I have a diecast machine that is overheating and I am looking at either adding to the existing unit or replacing it.

  3. Stewart Bailey says:

    looking at beginning manufacture of an aftermarket Volvo penta TAMD41 aftercooler. replacing an aluminum 228mm x254mm x 101.6. Operating temperatures will be around 104C saltwater will filter though the copper tubes to cool incoming turbo air (193kPa).

    On the long end I need 63mm exhaust inlet strait connection.

    On one side I need a nipple to attach water 25mm rubber tubing.

    total exchange 19.2 m3/min (on air side)

    no longer then 360mm

    no wider then 250mm

    no deeper then 280mm

  4. ROBERT GARRETT says:

    I HAVE A SULLAIR HEAT EXCHANGER PART # 040751 SERIAL # S077856-101 . I AM LOOKING FOR A QUOTE 2 NEW UNITS , IF YOU COULD HELP ME WITH THIS I WOULD GREATLY APPRICATE IT.

    THANK YOU
    ROBERT GARRETT

  5. Mark herdman says:

    Can you please give me a price and availability for the
    OR100 Hydraulic Oil Cooler.Please include delivery to France

Leave a Reply

Your email address will not be published. Required fields are marked *

Optionally add an image (JPEG only)