logo

January, 2015

now browsing by month

 

Oil Mist Collector For Cooking

Oil Mist Collector For Cooking 1

Oil Mist Collector For Cooking

Oil Mist Collector For Cooking

Item: Oil Mist Collector For Cooking,Electrostatic Air Purifier

Short Description: Oil Mist Collector For Industry,For CNC workshop,a best advanced air filter and air cleaner.Use electronic technology, can effectively clean industry oil foggy,and so,they are used in factories and workshops to improve the work place environment.They are designed especially for coolant and machine oil to help to reduce the oil content in the air.This oil content in air factories causes foggy air, slippery floor and health related problems.

Main Features and Advantages: One-time investment,Life-time with 0 cost for maintenance;Washable,no need to replace filters;High filter effience;Small windrop.

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Oil Mist Collector For Cooking
Models & Details for “Oil Mist Collector For Cooking”

Electrostatic Oil Mist Collector is mainly used for kitchen fume purification, industrial exhaust gas purification, CNC machine mist purification, material selection aluminum and Teflon insulation. Two-stage high pressure were 12000V and 6000V; different models of a variety of compliance with air volume mist, fume purification used in all production processes precision stamping dies, long service life.

Purification methods:

When the foggy(contained oil) is exhaust into the pipe,they are  first to enter the primary device – purifying rectifier room, using gravity inertia purification technology, the special structure of the large size of indoor pollutants gradually graded physical separation and balance rectification. Separated oil droplets flow into the sump discharge of large particles under the action of its own weight. The remaining small particle contaminants from entering the secondary device – high voltage electrostatic field, electrostatic field part two, the first stage of ionization, a strong electric field of charged particles become charged particles, these charged particles reach the second level set immediately after the dust-collecting electrode adsorption, and some charring. Meanwhile, the high-voltage electrostatic field effectively degrade harmful ingredients, played disinfection, deodorization effect. Finally, through the grille, clean air from the outdoors.

The role of oil mist purifier
Reduce the impact on employees:
0.3 ~ 3.5UM mist particles will remain in the body, pose a health hazard.
Reduce accidents at work:
Oil mist deposited the work area, floors, walkways slippery, easy to create wrestling accident.
Reduce fire hazards:
Oil deposited on the walls, the ceiling, forming a potential fire hazard on the device.
Reduced consumption of coolant:
Mist recovered can be reused for the plant to reduce the economic costs of coolant.

Mist purifier Features

● durable and efficient filtration efficiency; in addition to the smoke, excellent defogging performance. Electrostatic air purification device can capture almost all the fine dust and mist droplets demisting high efficiency (99%), and maintain long-term stable.
● Easy to install, each collector can be mounted directly on the machine, on the stand, easy assembly and disassembly;
● Maintenance is simple, easy to clean, no need to replace the filter, permanent use;
● small pressure loss, low energy consumption. Electrostatic air cleaning device is the use of the Coulomb force collecting dust, so only the burden of carrying the flue gas fan and therefore little resistance to airflow 100 ~ 300Pa. Further, although the operating voltage electrostatic air cleaning apparatus itself is high, but the current is very small, and therefore, electrostatic air cleaning device of electric power consumed is very small.

Applications:

●Cooking
●machinery industry.Universal lathes, CNC lathes, CNC lathes, vertical machining centers, CNC milling, EDM machines, cylindrical grinder, internal grinder, EDM.

● spray job
Washing machines, anti-rust oil spray coolant spraying.
● Other
Large mechanical bearing lubrication process, the mold process, the exhaust cylinder, the lens polishing.

Oil-Mist-Collector

working-principle

Model

CC-GA30

CC-GA50-80

CC-GA200

Input

110-220V

220V

220V

Output

HV: 8KV

LV:4KV

HV: 12KV

LV:6KV

0-15KV

Item dimension

45X120X30mm

95X155X85mm

255X165X65mm

Electrostatic Air Cleaner for cooking

Use and maintenance
Under normal circumstances the cleaning cycle, quarterly or half a year, once cleaned.
Cleaning methods and cleaning costs themselves, do not ask a professional to clean, easy to save money. Direct rinse with tap water after cleaning will not have any impact on the electric field of purification efficiency, energy consumption and power consumption without affecting the impact resistance.
Life without replacement, the service life of 20 years.
Pipe cleaning pipe cleaning without the need for special occasions special circumstances can greatly reduce the number of cleanings.
Resistance energy consumption by about 20Pa, reduce air conditioning power consumption, energy savings of about 12%.
Wearing parts, supplies metal filters, electronic dust collector, no wearing parts, no consumables.

Buying Guide to “Oil Mist Collector For Cooking”
  • The Oil Mist Collector For Cooking is available for retail and wholesale;
  • The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
  • Accept bulk order with Container delivery;
  • Size can be customized
  • More types Oil Mist Collector For Cooking are not displayed on the web.If the item above doesn`t meet your requirement,please contact us to email: [email protected] ,we can supply a favourite item you need.
General Knowledge on “Oil Mist Collector For Cooking”

electronic-capture

Electronic air cleaner,also named Electronic air filter, is an advanced, high-tech air purification device.It combines efficient dust collection, sterilization, kill the virus, remove bad smell gas, degradation of organic waste in one unit. Its installation is simple and easy to use,high purification efficiency, lower manufacturing cost, high reliability, continuous operation without replacement,washable and low maintenance costs, etc.They are always used in the clean room,and it can protect or replace prefilter,Medium filter and HEPA filter.

Electronic air cleaner is components by metal filters, high voltage separator, baghouse, cold catalyst filter, lysozyme filter . Large size of dust particles in the air are the early effect filters, smaller particles into the air into the ionization region, has been given a high voltage ionization positive charge, while negatively charged plate through the dust when positively charged particles are adsorb dust board. A strong electric field can be produced high energy plasma breakdown particles adhered bacterial surface, viral and microbial cell wall, cytoplasm or nucleus thoroughly destroy the cell electrolyte balance, which rapidly kill. In the process of generating plasma, high-frequency discharge opening instant high-energy chemical bonds of certain hazardous gas molecules to break down into harmless molecules elemental or plasma contains a large number of high-energy electrons, ions, excited particles and have strong oxidizing hydroxyl radical, the average energy of these particles is higher than the bond energy of active harmful gas molecules, they are harmful gas molecules frequently collide, open harmful gas molecular bond, while there will be a large amount of OH, HO2 , O and other highly oxidizing free radicals and O3, they react chemically with the harmful gas molecules generate harmless product, polluted air full of clean governance.

Features:

1, purifying air volume: clean air volume unit is 2000 ~ 3500m3 /h, can be combined using the maximum air volume limit.

2, can be made using a flexible combination according to customer requirements, new docking central air inlet and return air.

3, the application flexible and diverse, with air conditioning systems with the use of air-handling equipment can also be used as duct air purifiers, piping connected to the air supply system or return air system, as well as send, return air static press box.

4, automatically adjust the electric field strength, so that the purification equipment in the long run remains a high purification rate. Its working status clearly indicated by the lights.

5, easy to control, provides three switch shock signal management system for dust-free link to use.

6, well-designed security system-wide, high-voltage power supply unit body epoxy designed to tightly closed, safe and reliable.

7, static power control system with automatic overcurrent and overvoltage protection device to ensure stable operation of equipment. Faulty operation or long periods of cleaning, air purifier will automatically stop working.

8, low maintenance cost, you can wash with water directly, without affecting the purification efficiency.

9, easy to install and easy to use….

HVAC Parts >> Ventilation Materials >>  Electronic Air Cleaner >>Oil Mist Collector For Cooking

Electrostatic oil mist collector

Oil Mist Collector For Cooking 2

Electrostatic oil mist collector

Electrostatic oil mist collector

Item: Electrostatic oil mist collector

Short Description: Oil Mist Collector For Industry,For CNC workshop,a best advanced air filter and air cleaner.Use electronic technology, can effectively clean industry oil foggy,and so,they are used in factories and workshops to improve the work place environment.They are designed especially for coolant and machine oil to help to reduce the oil content in the air.This oil content in air factories causes foggy air, slippery floor and health related problems.

Main Features and Advantages: One-time investment,Life-time with 0 cost for maintenance;Washable,no need to replace filters;High filter effience;Small windrop.

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Electrostatic oil mist collector
Models & Details for “Electrostatic oil mist collector”

Electrostatic Oil Mist Collector is mainly used for kitchen fume purification, industrial exhaust gas purification, CNC machine mist purification, material selection aluminum and Teflon insulation. Two-stage high pressure were 12000V and 6000V; different models of a variety of compliance with air volume mist, fume purification used in all production processes precision stamping dies, long service life.

Purification methods:

When the foggy(contained oil) is exhaust into the pipe,they are  first to enter the primary device – purifying rectifier room, using gravity inertia purification technology, the special structure of the large size of indoor pollutants gradually graded physical separation and balance rectification. Separated oil droplets flow into the sump discharge of large particles under the action of its own weight. The remaining small particle contaminants from entering the secondary device – high voltage electrostatic field, electrostatic field part two, the first stage of ionization, a strong electric field of charged particles become charged particles, these charged particles reach the second level set immediately after the dust-collecting electrode adsorption, and some charring. Meanwhile, the high-voltage electrostatic field effectively degrade harmful ingredients, played disinfection, deodorization effect. Finally, through the grille, clean air from the outdoors.

The role of oil mist purifier
Reduce the impact on employees:
0.3 ~ 3.5UM mist particles will remain in the body, pose a health hazard.
Reduce accidents at work:
Oil mist deposited the work area, floors, walkways slippery, easy to create wrestling accident.
Reduce fire hazards:
Oil deposited on the walls, the ceiling, forming a potential fire hazard on the device.
Reduced consumption of coolant:
Mist recovered can be reused for the plant to reduce the economic costs of coolant.

Mist purifier Features

● durable and efficient filtration efficiency; in addition to the smoke, excellent defogging performance. Electrostatic air purification device can capture almost all the fine dust and mist droplets demisting high efficiency (99%), and maintain long-term stable.
● Easy to install, each collector can be mounted directly on the machine, on the stand, easy assembly and disassembly;
● Maintenance is simple, easy to clean, no need to replace the filter, permanent use;
● small pressure loss, low energy consumption. Electrostatic air cleaning device is the use of the Coulomb force collecting dust, so only the burden of carrying the flue gas fan and therefore little resistance to airflow 100 ~ 300Pa. Further, although the operating voltage electrostatic air cleaning apparatus itself is high, but the current is very small, and therefore, electrostatic air cleaning device of electric power consumed is very small.

Applications:

●Cooking
●machinery industry.Universal lathes, CNC lathes, CNC lathes, vertical machining centers, CNC milling, EDM machines, cylindrical grinder, internal grinder, EDM.

● spray job
Washing machines, anti-rust oil spray coolant spraying.
● Other
Large mechanical bearing lubrication process, the mold process, the exhaust cylinder, the lens polishing.

oil fog electronic collectorworking-principle

Model

Dimension(mm)

Air Volume(m³/h)

4803

A480XF255XT340mm

650

4804

A480XF300XT340mm

1100

4805

A480XF350XT340mm

1550

4806

A480XF400XT340mm

2000

4807

A480XF450XT340mm

2450

4808

A480XF500XT340mm2900

4809

A480XF550XT340mm3300

4810

A480XF600XT340mm

3800

Use and maintenance
Under normal circumstances the cleaning cycle, quarterly or half a year, once cleaned.
Cleaning methods and cleaning costs themselves, do not ask a professional to clean, easy to save money. Direct rinse with tap water after cleaning will not have any impact on the electric field of purification efficiency, energy consumption and power consumption without affecting the impact resistance.
Life without replacement, the service life of 20 years.
Pipe cleaning pipe cleaning without the need for special occasions special circumstances can greatly reduce the number of cleanings.
Resistance energy consumption by about 20Pa, reduce air conditioning power consumption, energy savings of about 12%.
Wearing parts, supplies metal filters, electronic dust collector, no wearing parts, no consumables.

Buying Guide to “Electrostatic oil mist collector”
  • The Electrostatic oil mist collector is available for retail and wholesale;
  • The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
  • Accept bulk order with Container delivery;
  • Size can be customized
  • More types Electrostatic oil mist collector are not displayed on the web.If the item above doesn`t meet your requirement,please contact us to email: [email protected] ,we can supply a favourite item you need.
General Knowledge on “Electrostatic oil mist collector”

electronic-capture

Electronic air cleaner,also named Electronic air filter, is an advanced, high-tech air purification device.It combines efficient dust collection, sterilization, kill the virus, remove bad smell gas, degradation of organic waste in one unit. Its installation is simple and easy to use,high purification efficiency, lower manufacturing cost, high reliability, continuous operation without replacement,washable and low maintenance costs, etc.They are always used in the clean room,and it can protect or replace prefilter,Medium filter and HEPA filter.

Electronic air cleaner is components by metal filters, high voltage separator, baghouse, cold catalyst filter, lysozyme filter . Large size of dust particles in the air are the early effect filters, smaller particles into the air into the ionization region, has been given a high voltage ionization positive charge, while negatively charged plate through the dust when positively charged particles are adsorb dust board. A strong electric field can be produced high energy plasma breakdown particles adhered bacterial surface, viral and microbial cell wall, cytoplasm or nucleus thoroughly destroy the cell electrolyte balance, which rapidly kill. In the process of generating plasma, high-frequency discharge opening instant high-energy chemical bonds of certain hazardous gas molecules to break down into harmless molecules elemental or plasma contains a large number of high-energy electrons, ions, excited particles and have strong oxidizing hydroxyl radical, the average energy of these particles is higher than the bond energy of active harmful gas molecules, they are harmful gas molecules frequently collide, open harmful gas molecular bond, while there will be a large amount of OH, HO2 , O and other highly oxidizing free radicals and O3, they react chemically with the harmful gas molecules generate harmless product, polluted air full of clean governance.

Features:

1, purifying air volume: clean air volume unit is 2000 ~ 3500m3 /h, can be combined using the maximum air volume limit.

2, can be made using a flexible combination according to customer requirements, new docking central air inlet and return air.

3, the application flexible and diverse, with air conditioning systems with the use of air-handling equipment can also be used as duct air purifiers, piping connected to the air supply system or return air system, as well as send, return air static press box.

4, automatically adjust the electric field strength, so that the purification equipment in the long run remains a high purification rate. Its working status clearly indicated by the lights.

5, easy to control, provides three switch shock signal management system for dust-free link to use.

6, well-designed security system-wide, high-voltage power supply unit body epoxy designed to tightly closed, safe and reliable.

7, static power control system with automatic overcurrent and overvoltage protection device to ensure stable operation of equipment. Faulty operation or long periods of cleaning, air purifier will automatically stop working.

8, low maintenance cost, you can wash with water directly, without affecting the purification efficiency.

9, easy to install and easy to use….

HVAC Parts >> Ventilation Materials >>  Electronic Air Cleaner >>Electrostatic oil mist collector

Oil Mist Collector For Industry

Oil Mist Collector For Cooking 3

Oil Mist Collector For Industry

Oil Mist Collector For Industry

Item: Oil Mist Collector For Industry,Electrostatic Air Purifier

Short Description: Oil Mist Collector For Industry,For CNC workshop,a best advanced air filter and air cleaner.Use electronic technology, can effectively clean industry oil foggy,and so,they are used in factories and workshops to improve the work place environment.They are designed especially for coolant and machine oil to help to reduce the oil content in the air.This oil content in air factories causes foggy air, slippery floor and health related problems.

Main Features and Advantages: One-time investment,Life-time with 0 cost for maintenance;Washable,no need to replace filters;High filter effience;Small windrop.

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Oil Mist Collector For Industry
Models & Details for “Oil Mist Collector For Industry”

Electrostatic Oil Mist Collector is mainly used for kitchen fume purification, industrial exhaust gas purification, CNC machine mist purification, material selection aluminum and Teflon insulation. Two-stage high pressure were 12000V and 6000V; different models of a variety of compliance with air volume mist, fume purification used in all production processes precision stamping dies, long service life.

Purification methods:

When the foggy(contained oil) is exhaust into the pipe,they are  first to enter the primary device – purifying rectifier room, using gravity inertia purification technology, the special structure of the large size of indoor pollutants gradually graded physical separation and balance rectification. Separated oil droplets flow into the sump discharge of large particles under the action of its own weight. The remaining small particle contaminants from entering the secondary device – high voltage electrostatic field, electrostatic field part two, the first stage of ionization, a strong electric field of charged particles become charged particles, these charged particles reach the second level set immediately after the dust-collecting electrode adsorption, and some charring. Meanwhile, the high-voltage electrostatic field effectively degrade harmful ingredients, played disinfection, deodorization effect. Finally, through the grille, clean air from the outdoors.

The role of oil mist purifier
Reduce the impact on employees:
0.3 ~ 3.5UM mist particles will remain in the body, pose a health hazard.
Reduce accidents at work:
Oil mist deposited the work area, floors, walkways slippery, easy to create wrestling accident.
Reduce fire hazards:
Oil deposited on the walls, the ceiling, forming a potential fire hazard on the device.
Reduced consumption of coolant:
Mist recovered can be reused for the plant to reduce the economic costs of coolant.

Mist purifier Features

● durable and efficient filtration efficiency; in addition to the smoke, excellent defogging performance. Electrostatic air purification device can capture almost all the fine dust and mist droplets demisting high efficiency (99%), and maintain long-term stable.
● Easy to install, each collector can be mounted directly on the machine, on the stand, easy assembly and disassembly;
● Maintenance is simple, easy to clean, no need to replace the filter, permanent use;
● small pressure loss, low energy consumption. Electrostatic air cleaning device is the use of the Coulomb force collecting dust, so only the burden of carrying the flue gas fan and therefore little resistance to airflow 100 ~ 300Pa. Further, although the operating voltage electrostatic air cleaning apparatus itself is high, but the current is very small, and therefore, electrostatic air cleaning device of electric power consumed is very small.

Applications:
● machinery industry
Universal lathes, CNC lathes, CNC lathes, vertical machining centers, CNC milling, EDM machines, cylindrical grinder, internal grinder, EDM.
● spray job
Washing machines, anti-rust oil spray coolant spraying.
● Other
Large mechanical bearing lubrication process, the mold process, the exhaust cylinder, the lens polishing.

Oil-Mist-Collector

Model

CC-GA30

CC-GA50-80

CC-GA200

Input

110-220V

220V

220V

Output

HV: 8KV

LV:4KV

HV: 12KV

LV:6KV

0-15KV

Item dimension

45X120X30mm

95X155X85mm

255X165X65mm

application-for-Oil Mist Collector

Use and maintenance
Under normal circumstances the cleaning cycle, quarterly or half a year, once cleaned.
Cleaning methods and cleaning costs themselves, do not ask a professional to clean, easy to save money. Direct rinse with tap water after cleaning will not have any impact on the electric field of purification efficiency, energy consumption and power consumption without affecting the impact resistance.
Life without replacement, the service life of 20 years.
Pipe cleaning pipe cleaning without the need for special occasions special circumstances can greatly reduce the number of cleanings.
Resistance energy consumption by about 20Pa, reduce air conditioning power consumption, energy savings of about 12%.
Wearing parts, supplies metal filters, electronic dust collector, no wearing parts, no consumables.

Buying Guide to “Oil Mist Collector For Industry”
  • The Oil Mist Collector For Industry is available for retail and wholesale;
  • The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
  • Accept bulk order with Container delivery;
  • Size can be customized
  • More types Oil Mist Collector For Industry are not displayed on the web.If the item above doesn`t meet your requirement,please contact us to email: [email protected] ,we can supply a favourite item you need.
General Knowledge on “Oil Mist Collector For Industry”

electronic-capture

Electronic air cleaner,also named Electronic air filter, is an advanced, high-tech air purification device.It combines efficient dust collection, sterilization, kill the virus, remove bad smell gas, degradation of organic waste in one unit. Its installation is simple and easy to use,high purification efficiency, lower manufacturing cost, high reliability, continuous operation without replacement,washable and low maintenance costs, etc.They are always used in the clean room,and it can protect or replace prefilter,Medium filter and HEPA filter.

Electronic air cleaner is components by metal filters, high voltage separator, baghouse, cold catalyst filter, lysozyme filter . Large size of dust particles in the air are the early effect filters, smaller particles into the air into the ionization region, has been given a high voltage ionization positive charge, while negatively charged plate through the dust when positively charged particles are adsorb dust board. A strong electric field can be produced high energy plasma breakdown particles adhered bacterial surface, viral and microbial cell wall, cytoplasm or nucleus thoroughly destroy the cell electrolyte balance, which rapidly kill. In the process of generating plasma, high-frequency discharge opening instant high-energy chemical bonds of certain hazardous gas molecules to break down into harmless molecules elemental or plasma contains a large number of high-energy electrons, ions, excited particles and have strong oxidizing hydroxyl radical, the average energy of these particles is higher than the bond energy of active harmful gas molecules, they are harmful gas molecules frequently collide, open harmful gas molecular bond, while there will be a large amount of OH, HO2 , O and other highly oxidizing free radicals and O3, they react chemically with the harmful gas molecules generate harmless product, polluted air full of clean governance.

Features:

1, purifying air volume: clean air volume unit is 2000 ~ 3500m3 /h, can be combined using the maximum air volume limit.

2, can be made using a flexible combination according to customer requirements, new docking central air inlet and return air.

3, the application flexible and diverse, with air conditioning systems with the use of air-handling equipment can also be used as duct air purifiers, piping connected to the air supply system or return air system, as well as send, return air static press box.

4, automatically adjust the electric field strength, so that the purification equipment in the long run remains a high purification rate. Its working status clearly indicated by the lights.

5, easy to control, provides three switch shock signal management system for dust-free link to use.

6, well-designed security system-wide, high-voltage power supply unit body epoxy designed to tightly closed, safe and reliable.

7, static power control system with automatic overcurrent and overvoltage protection device to ensure stable operation of equipment. Faulty operation or long periods of cleaning, air purifier will automatically stop working.

8, low maintenance cost, you can wash with water directly, without affecting the purification efficiency.

9, easy to install and easy to use….

HVAC Parts >> Ventilation Materials >>  Electronic Air Cleaner >>Oil Mist Collector For Industry

HVAC cryogenic liquid pump Failure cause and troubleshooting

Failure cause and troubleshooting, cryogenic liquid pumps:

Reason 1, the pump is activated, the outlet pressure rises on

⑴ does not match the direction of rotation of the impeller.
B pump not fully cooled, gas pump.

Exclude 1:

⑴ two-phase motor input line switch wiring
B cool and open the control valve or adjust the gas pressure.

Reason 2, pump head or flow insufficient.

⑴ the motor speed is insufficient.
B impeller blocked pipes.
C due to the seal pressure is too large, there is too much air into the pump.

Excluding 2:

⑴ increases speed.        B cleaning. C adjust the gas pressure.

Reason 3, liquid not indicating pressure jumping

⑴ unopened pipeline valves or piping resistance.
⑵ pipeline leak.

Excluding 3:

⑴ opening or cleaning. B repair

Reason 4, motor temperature rise.

⑴ motor problems.
B impeller ring has been wiped.
⑶ Labyrinth has been rubbed.

Exclude 4:

⑴ electrical repairs.         B adjust the clearance. C adjust the clearance.

Reason 5, stopping suddenly

⑴ chain of low gas pressure.
B bearing jammed inside.
Excluding 5:

⑴ adjustment pressures. B cleaning or replacement.

Reason 6, vibration or noise

⑴ the airframe and rotor misalignment.
B pump inlet pressure is too low cavitation arising or for any other reason.
C friction between moving parts and fixtures
⑷ rotor parts loose.

Excluding 6:

B ⑴ adjustment adjustment pressures, outgassing. D c correction test

II, a few liquid pump accident analysis

(1) the improvement put into initial regulation AR, drive West, AR pump, outlet pressure on how not to, using full cold, frequency is the highest, check the filter screen, wall insulation inspection, import and export pipe process, there is no effect, manufacturer commissioning personnel are also at a loss. Drive East, argon pump, pressure very quickly, is operating normally. Overhaul after PA towers, discovery West of argon pump inlet pipework is not reasonable, too many elbows, crude argon Tata II Kettle run low, imports argon pump NPSH is not up to the design value, outlet pressure does not go on. Inlet pipe reconstruction, reducing elbows. Restart, all is well.

(2) for AR pump outlet tube cracked at the top, stopping after repair, restart, argon pump found to be running soon, pressure falls, after heated Jet, and then start, and still is, Tata cauldron II liquids drain back fluid, argon pump still does not run correctly. At last the grilled argon pump cold box, remove the inlet strainer screen, problem is solved. Analysts believe that the II entered the perlite in the tower because: argon pump outlet tube top craze, after parking, leakage of perlite, again flows to the crude argon ⅰ top, heating by distillate gas pipeline flowing into the crude argon II Tower.
(3) the argon pump nitrogen gas began to use pressure, soon found that mixed gas discharge tube sealing system liquid discharge, analysts believe gas plug, using micro water pressure nitrogen Analyzer, found water near 1000PPm, which is due to nitrogen piston compressor cooling water leakage steel sleeve is not tight, cause to find the problem. Seal gas using instrument air, argon pump is operating normally.

(4) the first transformation, by cancellation of pure argon column flow, semen purity of trace nitrogen in argon have been unqualified, suspected to be caused by gas leakage study decided to seal gas switch to pump discharge pressure of argon argon, argon results semen still unqualified sealing gas reverted instrument air. Final phase II modification, the addition of pure argon column after semen argon qualified.

(5) in early August this year, running East ar pump found overnight, to switch to the argon pump starts, the speed can only moved to 2900 r/min, pump discharge pressure is about 0.58Mpa, liquid crude Argon is not playing I top. Electrician after consultation with the manufacturer, to refit the converter, speed up to 3600 r/min, pump discharge pressure up to 0.8Mpa, smooth scored first the top of the liquid.

Third, liquid pump suddenly stops the effects of air separation system

Liquid oxygen pumps for use in liquid oxygen adsorption of sudden stops have little effect on air separation systems, mainly to look for is safety, take main cooling liquid oxygen impurity analysis, enhanced liquid oxygen emissions, among other measures. Some liquid pump bursting stopped on empty points system effects is big, (1) no hydrogen business argon process in the of cycle rough liquid argon pump bursting stopped, rough argon condensation device still in work, liquefied of large liquid saved in rough argon II Tower bottom, cannot returned to rough argon ⅰ Tower participate in fine distillation, again returned to Shang Tower, such will makes rough argon ⅰ Tower Department containing oxygen quickly increased, main cold liquid oxygen liquid bit sharply reduced, main cold liquid oxygen liquid bit low a is not conducive to security; II is for hot area reduced, air eat not recently, oxygen production declined, makes main workers condition fluctuations is big. (2) the Tower up and down loop in a separate process in liquid oxygen pump suddenly stops, liquid oxygen and a lot of accumulated in the bottom of the Tower, go back to the main condenser will also cause the main cooling liquid oxygen level significantly lower results as above, and nitrogen can also occur. So for these two processes, the pump suddenly stopped, to quickly restore normal pumping, careful operation, ensuring a steady uninterrupted flow (hydrogen-free argon flow of liquid argon volume suddenly increases, it will pollute the main cooling liquid oxygen, oxygen purity down, even n. )。 (3) for internal compression process of liquid pump suddenly stopped, may affect the product the supply of oxygen, nitrogen and argon. Following experience of liquid argon pump pump operating on several points:

First reasonable of cycle argon pump process on pump of security run and the smooth pour pump is important, Figure 4 by shows process compared reasonable, each Taiwan argon pump each has a article independent of imports tube, to ensure to cold, and switching alternate pump Shi not effects run pump; filter device, and compensation device, and check back valve, and safety valve of set as Qian by said; addition argon pump export return pipeline cannot too fine, otherwise full return Shi pump of pressure high, not conducive to pump of security; heating valve to loaded in pump Hou, to guarantee heating Shi, can put filter device Shang of impurities blow except clean. An advanced process is, two pumps for liquids with a ready, low speed operation the backup pump is cold, when the primary pump failure after shutdown, standby pump running immediately, make the total device operation is not affected.

Right of pour pump operation is: on alternate pump for to cold, and started, as fifth items “centrifugal type liquid pump of started” by said for, must note of is, because to cold to consumption must of containing argon 98% around rough liquid argon, to rough argon ⅰ Tower Department Regulation valve will automatically shut small, rough argon ⅰ Tower of return than reduced, makes rough argon purity variable bad, trace oxygen rose, so, to cold Shi to corresponding reduced rough argon production, to keep purity stable. Spare pump starts after the stop running the pump immediately, being careful to ensure crude argon flow ⅰ Tower stable, do not fluctuate, otherwise it will affect the main tower operating mode. (From the Internet)

Metal Spinning Fabrication,Custom Metal Spun products

Oil Mist Collector For Cooking 4

Metal Spinning Fabrication,Custom Metal Spun products

metal spimming-2

Service: Metal Spinning Fabrication,Custom Metal Spun products

Metal spinning is a forming process that produces hollow parts that are typically circular in cross-section. The basic metal spinning process starts with a flat metal disc (blank), which rotates on a lathe. This rotating blank is pressed against a tool (chuck mandrel) that duplicates the interior of the part.The basic metal spun shapes are the hemisphere, cone, cylindrical shell and venturi to name a few. Parts produced from metal spinning are utilized in many industries: agricultural, food service,lighting, marine, automotive, Commercial and industrial roofing,commercial and residential lighting, bearing closures, air pollution and ventilation, custom display stands, funeral urns, industrial vacuum cleaners, flag stand bases, fireplace accessories andsatellite dish manufacturers.

Place of origin: China , Service to worldwide.

Want “ Metal Spinning Fabrication”? Click and Inquiry it
Experienced spun metal products 

experienced spun metal products-1 experienced spun metal products-2

Equipments for Metal Spinning Fabrication

spinning-equipments

Materials for Metal Spinning Fabrication

Aluminum Metal Spinning and Stamping

Metal Craft Spinning and Stamping (MCSS) is specialized in Spinning Aluminum of various sizes and alloys. Our Aluminum products have the ability to be polished to the highest standard of commercial industries.

Brass Metal Spinning and Stamping

Metal Craft Spinning and Stamping (MCSS) commonly makes use of Brass for decorative metal applications. Brass is a formable metal that is receptive to many different finishing purposes.

Copper Metal Spinning

The Copper parts produced by Metal Craft Spinning and Stamping are used for lighting, roofing and decorative purposes since copper is a popular alloy that is known for its heat resistant abilities.

Steel Metal Spinning

Steel, a metal that is easy to work with is quite popular for its spinning applications. As well, the steel components are very popular due to its strength and durability characteristics.

Stainless Steel Metal Spinning

Stainless Steel has proved to serve various special metal spinning applications. Some of its well known properties include durability, strength, and non-corrosiveness. Its common uses are on exposed exterior applications.

Shapes for “Metal Spinning” 

metal spimming-2metal spinning-1metal spimming shapes

General knowledge on “Metal Tube” for fabrication

Typical Stages Of Part Development

  • Prepare a drawing of the metal piece that is to be spun on the lathe
  • Make tooling of the appropriate shape.
  • Cut the metal disc corresponding to the piece.
  • Start lathe and select proper cutting tool
  • Insert the metal spinning pin in the t-bar rest. Adjust rest so that the tool is at a slight angle against the pin.
  • Apply waxy lubrication to the outer surface of the metal spinning on the lathe.
  • Hold the tool with right hand placing the handle under your arm
  • Apply pressure to the metal spinning on the lathe by moving the tool from the center to the outer edge of the metal.
    Safety
Submit drawings for Metal Spinning Fabrication,Custom Metal Spun products

business procedures for Metal Spinning Fabrication,Custom Metal Spun products

Request Quotation for Metal Spinning Fabrication,Custom Metal Spun products,Let China metal factory serve for you:

[contact-form-7 id=”19″ title=”Contact form 1″]

Metal Spinning Fabrication,Custom Metal Spun productsCustom Manufacturing Products >>Metal Products Fabricate In China  >>Metal Spinning Fabrication,Custom Metal Spun products

Commercial Thermodynamic Solar Panel Hot Water System

Oil Mist Collector For Cooking 5

Commercial Thermodynamic Solar Panel Hot Water System

Commercial Thermodynamic Solar Panel Hot Water System

Item: Commercial Thermodynamic Solar Panel Hot Water System(Also used for Industry)

Short Description: A large heat block with thermodynamic solar panel absorbing energy from enviroment,to heat large volume water.Double ways to absorb heat energy from  solar,cloudy,night, rain,even from snow.Save energy 80%.Commerical purpose,and they are usally work for the large hot water project for school, hospital, hotel,goverment,etc.

Main Feature: Work with thermodynamic panel together.Double ways to absorb energy,from air and from solar,rain,wind,snow…High COP,save 80% energy.Can work in low temperature.

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Commercial Thermodynamic Solar Panel Hot Water System
Models & Details for “Commercial Thermodynamic Solar Panel Hot Water System”

The model for commercial project can be divided into: TSP10 & TSP02 as flowing:

ModelTSP10TSP20
Power~380V 50H/60Z~380V 50H/60Z
Rated Water Output Temperature55℃55℃
Maximum Water Output Temperature65℃65℃
Rated  Heat Capacity Output (W)12000W30000W
Rated Power Input(W)3000W7500W
Rated Current Input(A)4.511.6
Noise   ( (dB) A)≤55≤ 60
Weight (kg)100180
Size (mm)800x500x8001000x600x1000
Hot water folow rate(L/hour)7001400
Pipe connecting threadG 3/4″G 1-1/4″
Panel Size(mm) & Panel Qty.1700×800, 6panel1700×800, 16 panel
Applicable Environment Temp.-20℃/50℃-20℃/50℃

Commerical Thermodynamic Solar Panel Hot Water System

Thermodynamic Solar Panel working

Buying Guide to “Commerical Thermodynamic Solar Panel Hot Water System”
  • The Commerical Thermodynamic Solar Panel Hot Water System is available for retail and wholesale;
  • The place of origin is in China,please consider freight into the cost;
  • Accept bulk order with Container delivery;
  • please contact us to email: [email protected]
General Knowledge on “Commercial Thermodynamic Solar Panel Hot Water System”

commercial thermoynamic panel system workingcommercial-water heater system working

HVAC Parts >> Solar Utilizing >>Solar Thermo Devices>>Thermodynamic Solar System>> Commercial Thermodynamic Solar Panel Hot Water System

Air conditioning hot and cold water system design and configuration

With the rapid development of China’s iron and steel industry, central air conditioning system in steel plant has been widely used, central air condition relative to the split air conditioner has the following advantages:

① Central air conditioning operation management flexibility, and running costs than split air conditioners, central air conditioning refrigeration station can directly control the start and stop time of refrigerator and cooling capacity size can be adjusted according to climate change to reduce operating cost.

II central air conditioning can guarantee deliveries to the room, and keep the room empty with the rapid development of China’s iron and steel industry, central air conditioning system in steel plant has been more widely used.

Central air conditioning in relation to split air conditioner has the following advantages:

① Central air conditioning operation management flexibility, and running costs than split air conditioners, central air conditioning refrigeration station can directly control the start and stop time of refrigerator and cooling capacity size can be adjusted according to climate change to reduce operating cost.

II central air conditioning can guarantee deliveries to the room, and keep the room air clean and sanitary. Split air conditioning only through doors, Windows, ventilation and fresh air ventilators, cooling capacity loss, which affects not only the room temperature, and a waste of energy.

③ Central air-conditioning fault less maintenance. Central air conditioning both for air conditioning units and air duct system or room fan-coil and fresh air system, were prone to failure, and refrigeration equipment are located within the cooling station, easy to repair. Split air conditioner split unit air conditioner all over everywhere, refrigeration compressors are not only plentiful but dispersed, a fault can hardly begin to repair their good.

④ air conditioning noise less than split air conditioning. Central air-conditioning retro-fitting noise reduction device to reduce noise, and split air conditioning compressor air conditioning rooms close, it is difficult to achieve noise reduction measures.

⑤ Central air conditioning ends form beautiful diverse, can and decoration construction close tie, pipeline and equipment are can hidden in ceiling within, guarantee building of beautiful, save indoor of using space; but points body air conditioning of wind cold type outdoor machine must scattered of hanging outside wall Shang or loaded Yu outdoor ground Shang, effects outside decoration effect, and indoor machine is must hanging in within wall Shang or placed in ground, and occupy has indoor space, this virtually reduced has room of area.

⑥ Central air conditioning air-conditioning condensation water can be concentrated at the end of discharge, but split air conditioner air conditioner layout scattered, condensate discharge is not easy to deal with.

For these reasons, using central air conditioning system is feasible in the steel mills, steel mills in the central air-conditioning system in relation to civil architecture has the following characteristics: ① steel mill air conditioner users scattered within air conditioning comparison many types of user, how to design air conditioning pipes to solve hydraulic maladjustment of air conditioning user, it is especially important to meet the needs of different users. ② steel pipes are quite complex, criss-crossing the network configuration as much as possible the economic compact is worth exploring, including outdoor insulation for hot and cold water piping practices is important, improper practices will directly affect the results. ③ Mills within the air conditioner user input to use at different times, air conditioning load change is big, take fully into account the unit automatically adjusts to changes in load.

Here two aspects from air conditioning machine rooms and air conditioning line to discuss steel plants in the air conditioning design should pay attention to the problem in order for your reference.

1, room design configurations

1.1 selection and configuration of chillers

Mills central air conditioning cold water unit of select should full considered factory within of energy configuration situation, for most Mills,, steelmaking and other process process will produced large of steam, from energy of angle for, in air conditioning cold water unit of select Shang should as considered using this part steam, so for has extra steam of mills, in cold water unit of select Shang should priority selection steam type bromide of lithium cold water unit, for same refrigeration volume of steam type bromide of lithium refrigerator group and electric refrigerator group,, Lithium bromide unit can be saving around 98%.

For chiller number option should try to avoid using a single machine, and in cases where conditions allow, can choose two or more of the chiller, which does not take into account the standby unit, and in the case of load changes, you can turn off some chillers, saving on running costs, you can make the unit run at a higher COP values. Chillers and chilled water pumps in ways corresponding to one by one can be used, such as limited by room size, more than one may be used independent chillers and chilled water pumps arranged in parallel. This arrangement has its obvious advantages in simplicity, and convenience, but should pay attention to in this way in the case of partial air-conditioning cooling load, part of the chiller in a closed state, if management operational management negligence, no chiller stopped running the pipeline valve closes, then freezing water bypass flow phenomenon occurs. Bypass flow will affect the efficiency of water chillers in cold water, reduce the COP values of chillers. If air-conditioning cooling load demand ends on the other hand, require an additional number of chillers, managers are required to timely, timely and open an additional pipeline valve in water chiller, the operations management is clearly in trouble. Most economic measures to resolve this conflict is introduced in the chiller piping electric butterfly valve. Electric butterfly valve, water chillers and chilled water pumps, cooling water pump designed to operate the chain controls, so you can in the largest energy-consuming air conditioning system part is saving the most promising region in the control of intelligent, most economic investment, the most energy-efficient and convenient management.

1.2 refrigeration pump selection and configuration

Large central air conditioning chilled water system, with the change of air conditioning cooling load, use cold water units, number of air conditioning chilled water pumps in the wake of changes in and flow of air conditioning cooling water system pipe network has changed, which caused water pipe network resistance to change. In low load run situation Xia, especially air conditioning cold pumps only needs single Taiwan run Shi, air conditioning cold water system full load and low load run Shi water resistance difference is big, this led to low load Shi air conditioning cold pumps Super flow run, its run work points may jumped out of economic regional, then caused motor efficiency of reduced, while pumps run power consumption of increased, so in only single Taiwan pumps run of workers condition Xia, very easy occurred motor overload burned of accident. So design in the cannot only note has more Taiwan pumps of rated State points can meet pipeline calculation requirements, also must attention air conditioning low load Shi run State points changes by raised of problem, and take necessary of solution measures, solution method has two species, a is frozen pumps used frequency technology, that parallel run of each pump in the, a Taiwan pump used frequency pump, it as low load Shi single Taiwan pumps run of fixed pump, in system Super flow Shi, the pump reduced running frequency, system of flow also with reduced, Chilled water pump by using frequency conversion technology is a system variable flow of energy-saving technologies. Another solution is to export of each pump fitted with a current-limiting valve, it can pump to prevent the backflow, replacing the traditional non-return valve, and can play a role in limiting flow of the working pump. The valve head can set a control, when the pump head is below the control valve closing motion lift so that actual working head increase, prevent motor in low-lift pump, high flow, low efficiency occurs when overload. This way for the first way, energy-saving effect is poor, but it would reduce investment, the system is easier to manage.

1.3 side pipeline control room accessories set

Pressure gauges, and thermometers are set for air conditioning water system in the engine room of the side part is particularly important, with pressure gauge readings can judge the hydraulic conditions of the water system is normal, with the thermometer settings can initially determines if the water flows through the pipeline to meet the requirements. Recommended in the backwater dry pipe into each set water separator should be installed until a thermometer, by observing the temperature thermometer can accurately grasp the distribution of cooling load. Large temperature difference between the way the valves can be opened, small temperature difference branch of the valve opening can be adjusted smaller. Each water tube thermometer, operation managers to cooling load distribution of intuitive control system.
1.4 system with constant pressure and water

Setting system pressure device to enable the system to the operating voltage to ensure the system does not empty, no vaporization. General central air conditioning system pressure points are located at the entrance to chilled water pumps on the backwater dry pipe, so you can make the pump produces pressure in the system has been an appropriate distribution. Current heating and air-conditioning system with constant pressure supply water main expansion tank water at constant pressure, filling pumps constant pressure supply water, gas constant pressure tank with fill water pumps constant pressure supply water, and so on. Expansion tank pressure water is most economical and easiest way, so now heavily used in civil construction, but the expansion tank must be located at the highest point of the system, iron, air conditioner users scattered, distance from maximum air conditioning facilities tend to be long, the expansion tank is difficult to decorate, management is not convenient, high limits the application of the water tank. Small pump pressure continuous make-up water system, its pressure is formed by filling the tank, fill the pump and the regulator, while the system is running, through the pressure regulator function, make small pump continuous replenishment of water leakage is compatible with the system so as to maintain the system of hydrodynamic curve, but this constant pressure, which normally takes continuous operation, low power consumption. Using pressure tank combines fill pumps of set pressure fill water device in steel industry in the was large using, it main by fill pumps, and diaphragm type pressure jug, and safety valve, and electric contact pressure table and electromagnetic valve composition, it of work principle following: Dang system prepared run Shi, opened fill pumps, water was sent to tube network of while also was sent to pressure jug of water room, water room expanded and will tank within of gas compression, tank within of pressure with of increased, Dang pressure increased to Supreme work pressure Shi (System Supreme points and set pressure points Zhijian of high poor plus 3~5mH2O), pumps stopped turned, system has full water, using pressure tank within of pressure to maintained tube network of pressure, dang system run process in the, due to system leaking or water temperature change led to system water volume reduced Shi, pressure tank within of water room narrowed, tank within gas expansion, pressure reduced, dang pressure reduced to system minimum work pressure Shi (System Supreme points and set pressure points Zhijian of high poor plus 1mH2O), pumps opened, System for filling water. Installations in the pressure gauge and the solenoid valve is a safety device, when overpressure, and through the pressure gauge and solenoid valve the excess water out of the system. Pressure tanks with pumps constant pressure supply water compensation device device selection and calculation procedure is as follows:

1.5 fill pump selection

System within of water, dang for hot or hot and cold dual-use Shi, should used softening water, dang softening water pressure cannot directly for into tank Shi, should another set pumps fill water, fill pumps of automatically fill water can by system cycle water of 1% considered, accident fill water by system cycle water of 3% considered, directly fill into cycle pumps of entrance, fill pumps of head should by fill water points and system Supreme points of high poor plus 3~5mH2O of rich volume considered.

1.6 selection of pressure tank

Maximum working pressure of the pressure tank should be greater than the small pump head.

Volume of the tank tank water volume should be selected, the tank water volume should be selected according to the volume of the expansion tank, and that the volume of water inside the tank should be able to accommodate the expansion of the water system.

Indoor machine loop heat pipe (temperature 25℃) 7.8

Outdoor mechanical loop heat pipe (temperature 25℃) 5.8

Internal machinery for cold (temperature 5 ℃) or cool-31.2

Outdoor mechanical circulatory cooling system (temperature 5 ℃) or cool-23.2

Boiler 2~5

Refrigeration of shell-and-tube evaporator 1

Steam-water or water-water heat exchanger 1

Cooling coil (hot and cold coil 1)

2, air-conditioning piping design configurations

2.1 main steelmaking plant in air-conditioning pipe configuration

With drive system than ISO drive system hydraulic workers condition more stable, flow distribution also more uniform, conducive to air conditioning water system of hydraulic balance, steel plant within of air conditioning competent line more is along plant column column line layout, so is easy take with program system (as figure by shows), but each air conditioning user due to distance air conditioning competent line of distance different, indoor layout situation different, hard used with program of layout (as Figure user 1~4 of indoor pipeline), Best solution for this is pressing economic specific frictional resistance determine the one farthest from the air conditioning in the mainline pressure loss pressure loss of the largest user, according to pressure loss to determine the other loops of pipe diameter, this allows flow of air conditioning in each user’s assigned demand, decreased workload. The pipeline inside the air conditioner users such as unconditional direct return scheme can be used, the terminal can be adjusted using a manual valve balancing valve.

2.2 main steelmaking workshop air conditioning pipeline configuration

General outdoor insulation pipe overhead laying trench for laying, laying three, overhead laying enterprise application often works in a factory, but some users relatively far from air conditioning facilities, as a good chunk of overhead piping, tends to affect the plant’s overall layout and affect the plant’s appearance. Addition regional heating for cold engineering often due to outdoor underground pipeline staggered and to set, common of underground pipeline has strong, and weak, and to drainage, and gas,, national specification on species pipeline set spacing has specific requirements, various outdoor pipeline should as reduced respective underground occupies space and will respective relationship straighten out, regional underground tube network party can effective implementation, this aspects straight buried than trench laying superior. Simple and sophisticated technology on engineering practice of application of polyurethane direct-buried pipes were analyzed and compared.

2.2.1 the structure and characteristics of thermal insulation direct-buried pipe

Prefabricated directly buried insulating pipe caused by the medium of steel pipes, coats, tube and pipe, and the outer casing is filled between the hydrophobic and made of non-combustible insulation layer of polyurethane combined prefabrication of pipe, insulation foam keep it closely together and the outer casing. Because direct-buried pipes, insulation and floor live loads directly under the pipeline and at the same time affected by ground moisture and groundwater, so insulation direct-buried pipes in waterproofing, anti-corrosion and high performance in terms of mechanical strength requirements and, therefore, only a buried pipe construction cost is high. But because of its comprehensive low cost, simple construction and trench laying compared savings volume of earthwork, concrete, brick works, construction schedule shortened by more than half. And actually not only directly buried insulating pipeline insulation effect, lower total cost, and in the case of strictly according to the requirements, thermal insulation of the physical Anatomy after six years service life analysis and artificial ageing tests confirmed in more than 15 years, and trench laying pipe insulation insulation material rock wool or cotton centrifugal 3-5 generally needs to be replaced again. To sum up, directly buried insulating pipe in heat preservation performance, investment, construction, maintenance and day-to-day running costs were a big lead.

2.2.2 design of directly buried insulating pipe

Because of the air conditioning with the maximum hot water temperature of 60 degrees centigrade, the lowest temperature was 7 degrees centigrade, so direct-buried under too much stress will not. General direct-buried pipes, seamless steel tubes or Q235 tube, material for the 20th, at 15 ° c above the temperature when installed directly buried heat-supply pipeline (<100 degrees) do not need to take any measures without installing pipelines buried underground in the form of compensation (without fixed bearing and compensator), the safe operation of the pipeline can be achieved. Therefore, for district heating and cooling (<100 ℃ water systems) installed without compensation is in the form of convenience, safety and economy. No-compensate directly-buried is friction between the soil and the outer sleeve fixed pipe. Piping finish laying should be preheated before covering pipe and pipelines without having to set compensator, usually don’t need fixed bracket. In order to reduce costs, while preheating water test. Of regional cooling and heating pipeline features tubes medium temperature is not high (<100), working pressure <1.0MPa, but the pipeline is long, straight sections are often hundreds of meters long. Friction is much larger than the thermal stress of the soil, occurred in the middle of the straight section “anchoring”, anchorage-side critical sections to stress checking so that it meets the allowable stress of steel. Use without compensation installation of directly buried heat-supply pipeline’s horizontal elbows, tees, stress concentration. At design time, and should stress calculation, select the appropriate pressure level of elbows and tees. In General, the supply and return water pipes for air conditioning, for safety’s sake, the choice of elbows and tees can be taken into account when using a pressure rating higher than the pipeline.

3, conclusion

1, central air conditioning system for steel mill hosts option, configuration should take full account of the plant’s energy situation, where there are rich steam, preference should be given-steam lithium bromide unit;

Air conditioner users within 2, for steel mills are scattered with expandable tank constant pressure supply water is more difficult, can be combined with pressure tank fill pump with constant pressure water supply equipment

3, factory air-conditioning in main line layout should be used with the program. Air conditioning design of user should be established in accordance with economic specific frictional resistance a farthest from the air conditioning in the mainline pressure loss is the largest user of pressure loss, according to pressure loss to determine the other loops of pipe diameter;

4, for district heating and cooling pipe of directly buried insulating pipeline can be used without compensation, it should be noted the “anchoring, and elbows, tees and other stress-calculation of stress concentration.

Through-Wall Ventilator

Oil Mist Collector For Cooking 6

Home>>Ventilation Material>>Air Terminal Devices>>Through-Wall Ventilator

Through-Wall-Ventilator

Item: Through-Wall Ventilator

Short Description: A Comprises high-quality non-mechanical ventilators which flow and filter fresh air into the room.Through-wall installation in domestic and commercial applications with distributeing multi ventilator to get clean and fresh air.The air flowing volume can be adjusted or stop by swirling the louvre. Made from quality plastic ABS and PVC-U.The inlet grille can be plastic or stainless steel(opition).Nice, durable service life, convenient installation. Is an energy-saving and environmental protection product.

Size:  Φ110mm, Φ160mm

Place of origin: China , Sell to worldwide.

Order or Inquiry on “Through-Wall Ventilator
Models & Details for “Through-Wall Ventilator”

Features:

  • Description:Through-Wall Ventilator;
  • Suitable for new build and refurbishment applications.
  • Consist of an internal controller, adjustable wall sleeve and external grille with rain deflector.
  • Material:Inlet and Outlet are made from ABS,the round pipe are made from PVC-U;
  • Non-mechanical ventilator,depends on natural wind to flow air;Air Volume flowing can be adjusted or stop;
  • Through-wall installation,Simple and easy to fit.
  • Filter fresh air,Provide added benefits such as noise reduction, condensation, environmental filtering, condensation control and energy saving.
  • filter out all pollen and other pollutants, helping prevent asthma attacks and improving the indoor air quality for occupants.
  • Size&Model: wall sleeve Φ110mm, Φ160mm.Pipe Long 380mm,it can be cut to fit your wall thickness.

through-wall-plastic-ventilatorthrough-the-wall-fresh-air-ventilatorthrough-wall-Exhaust-ventilator

Buying Guide to “Through-Wall Ventilator”
  • The Through-Wall Ventilator is available for retail and wholesale;
  • The place of origin is in China,when you buy one or a small quantity,please consider freight into the cost;
  • Accept bulk order with Container delivery;
  • The inlet can be plastic or stainless steel(opition);
  • More types of  Through-Wall Ventilator are not displayed on the web.If the item above doesn`t meet your requirement,please contact us to email: [email protected] ,we can supply a favourite item you need.
General Knowledge on “Through-Wall Ventilator ”

 

Metal Casting,Custom Casting Metal Parts

Oil Mist Collector For Cooking 7

Metal-Casting

Serive: Metal Casting,Custom Casting Metal Parts

Short Description:Die-casting is a metal casting process, which is characterized by using a mold cavity for applying a high pressure molten metal. The mold is usually processed with a higher strength alloy, this process is somewhat similar to injection molding. Most are non-ferrous die-casting, such as zinc, copper, aluminum, magnesium, lead, tin and pewter, and their alloys. Depending on the type of die-casting, requires the use of a cold chamber die casting machine or hot chamber die casting machine.

Material for casting: Aluminium,Zinc,Copper,Brass,Iron

Place of Origin: China, Serve for worldwide customers

Want “Metal casting parts”? Inquiry or Order it!
 Experienced products made with technology of Metal Casting

  

  

  

The usual metal for casting mainly include zinc, copper, aluminum, magnesium, lead, tin and pewter, although tpressuring cast iron is very rare, but it is also feasible. Special die-cast metal, including ZAMAK, standard aluminum-zinc alloy and the US Aluminum Association: AA380, AA384, AA386, AA390 and AZ91D magnesium. When various metal casting characteristics are as follows:
Zinc: most likely to die-cast metal, the manufacture of small parts is economical, easy coating, compressive strength, plasticity, long life cast.
Aluminum: light weight, high manufacturing complexity and thin-walled castings dimensional stability, corrosion resistance, good mechanical properties, high thermal and electrical conductivity, high temperature strength remains high.
Magnesium: Easy machining, strength to weight ratio, commonly used in the lightest metal casting.
Copper: high hardness, corrosion resistance, mechanical properties of die-cast metal used best, abrasion resistance, strength close to the steel.
Lead and tin: high density, high dimensional accuracy, corrosion can be used as special parts. Considerations of public health, this alloy can not be used in food processing, storage equipment. Tin antimony alloy (sometimes also contain a little copper) can be used to manufacture handmade type letterpress printing and hot stamping.

  Main Equipments for Custom Metal Casting parts

We specialize in design, research and manufacturing aluminum, copper and zinc alloy casting and forging products, which are  widely used in automotive ,vehicles, ships and machinery, etc.
We have strong techinical force, equipment, testing method and professional personnel . There are chemical element analyzers that can control and analyze product chemical element effectively.
Shot blasting machine,sand blasting machine and vibrative grinder which ensures the quality and surface finish;
Processing center, CNC milling machine,CNC lathe,ordinary lathe and drill press that can strictly control products size and precision.
We are mainly producing according to customer’s drawings or samples,and many thanks for your enquires.

metal-casting-equipments metal-casting-machines

 General Knowledge on “Metal Casting”

Metal Casting Benefits:
1. good quality
High precision casting size, generally the equivalent of 6 to 7, even up to four; good surface finish, usually equivalent to 5 to 8; high strength and hardness, strength than sand casting generally increased by 25 to 30%, but the extension rate reduced by approximately 70%; dimensional stability, good interchangeability; may die casting thin-walled complex castings. For example, the current minimum wall thickness of zinc alloy die castings up to 0.3mm; aluminum alloy castings of up to 0.5mm; the smallest aperture of cast 0.7mm; minimum pitch of 0.75mm.
2. High production efficiency
Machine production rate, such as domestic JⅢ3 horizontal cold air can be die-die-casting machine for eight hours on average 600 to 700, a small hot chamber die-casting machine per eight hours from 3000 to 7000 can; long life type-casting, a pair of die-casting type, bell-casting alloys, life up to hundreds of thousands, or even millions of times; easy mechanization and automation.
3. good economic effect
Because casting precise size, table pan clean and so on. Generally no longer be machined and used directly, or processing capacity is small, so not only improves the metal utilization, and reduces the amount of processing equipment and working hours; casting price will be easy; in combination with other die-cast metal or non-metal materials can be used . Saving metal assembly work and save.

Metal Casting Shortcoming
1) Because the liquid metal die-filled cavity high speed, flow regime is unstable, so the use of general-casting method, the casting is easy to produce pores, can not be heat;
2) on the concave complex castings, casting more difficult;
3) melting point alloys (such as copper, ferrous metals), the lower die-type life;
4) should not be small batch production, the main reason is the high cost of die-based manufacturing, die-casting machine production of high efficiency, small batch production uneconomical.

The biggest drawback is the cost of die-cast high. Casting equipment and molds, die casting method relative to other related components for all expensive. So when the production of a large number of products manufactured before casting more economical. Other disadvantages include: This process applies only to the higher mobility of metals and casting quality must be between 30 g and 10 kg.In the conventional die-casting, the casting of the last batch of castings always have pores. Thus any heat treatment or welding can not be performed, because the gas within the gap will be expanded under the action of heat, resulting in the release of micro-defects and internal surfaces.

Submit drawings for Customing Metal Casting Parts,Let Smartclima manufacture it for you

order procedures for casting

Request Quotation for Custom Metal Casting Parts,Let China metal factory serve for you:

[contact-form-7 id=”19″ title=”Contact form 1″] Metal Casting for many fieldsMetal Products Fabricate In China  >> Sheet Metal Stamping >>Metal Casting,Custom Casting Metal Parts

Custom Metal Stamping Parts

Oil Mist Collector For Cooking 8

custom metal stamping parts

Serive: Custom Metal Stamping Parts,Punching Metal Products

A process to fabricate sheet metal. For example,including chimney sheet production, drum, tank oiler, ventilation pipes, elbow size head, hemispherical dome, funnel-shaped.The main processes includes shearing, cutting,stamping,bending buckle side, bending forming, welding, riveting, etc. Corresponding process is casting, forging, machining parts, etc.The material for fabricating is Carbon steel sheet,Stainless steel,Aluminium Sheet,Copper Sheet .
Related Service:

Want “Custom Metal Stamping Parts”? Inquiry or Order it!
 Experienced products made with technology of Custom Metal Stamping Parts

Metal Stamping means to process steel sheet/plate/panel with technology of stamping,punching,cutting,bending,forming and deep-drawing by machines of punch,cut,bender,hydraulic press.The products of steel sheet stamping are widely used in the field of industry, agriculture, building, defense,  transporation,aerospace,electronics,datalink,etc.The surface of steel sheet stamping products are always polishing,powder painting,electroplating.Above all will be finished by Smartclima,who can be your best assistance in the metal products process.The following are a small part items we experienced.More items are not displayed.

Sheet Metal Stamping parts Sheet Metal bending parts CNC Punching sheet

hardware parts metal bracket mount metal sheet deep-drawing products

Sheet Metal Stamping partssheet metal deforming part stainless steel flanges

stainless steel bowl perforated sheet metal perforated stainless steel sheet

The materials for stamping process generally use cold-rolled plates (SPCC), hot-rolled plates (SHCC), galvanized sheet (SECC, SGCC), copper (CU) brass, copper, beryllium copper, aluminum (6061,5052, 1010,1060,6063, duralumin, etc.), aluminum, stainless steel (mirror, brushed, matte), according to the role of the different products, use of different materials, which normally takes from product use and cost up to consider it.

1. Cold-rolled plate SPCC, mainly used in electroplating and paint parts, low cost, easy to shape, material thickness ≤3.2mm.
2. Hot-rolled plates SHCC, material T≥3.0mm, also by electroplating, painting parts, low cost, but it is difficult shape, mainly used flat pieces.
3. Galvanized sheet SECC, SGCC. SECC electrolytic plate material points N, P material, N materials mainly without surface treatment, high costs, P material for coating parts.
4. Copper; the role of the main conductive materials and parts, the surface treatment is nickel, chrome, with or without treatment, high costs.
5. Aluminum; general surface chromate (J11-A), oxidation (conductive oxide, chemical oxidation), high cost, there are silver-plated, nickel-plated.
6. Aluminum; sectional structure of complex materials and parts used extensively for a variety of plug box. Surface treatment with aluminum.
7. Stainless steel; mainly used without any surface treatment,, high cost.

  Main Equipments for Custom Metal Stamping Parts

Sheet Metal Stamping Quotation

Steel sheet stamping Steel sheet flat spreading

We adope the technology of rolling and drawing to flat steel sheet automatically,controlled by computer,high precision on dimension. Count pieces number automatically.No need other worker to operate it after you put steel panel roll into the roll bar.The material thickness which can be processed is from 0.5mm to 5mm,and the width can be from 10mm to 800mm.The matericals which can be process is steel sheet,stainless steel sheet,aluminium sheet,copper sheet.Rolls state material  will be spread to flat and then automaticlly cut.Because of mechnical oil is sprayed on the working rolls,so,the surface of steel can be protected well.Then the cuted pieces are ready for next procedures. By this working technology,our working effience can be raised much.Working time is less than 80% and get more high precision.Especially, workers will be more safe when he is working/operating machine. Now,the machine has been one of our best machines to process steel sheet stamping products.

 

 

 

Steel sheet stamping Automatically cutting and punching

The machine of automatic cutting and punching is put ahead of steel sheet flad spreading machine.The flat sheet comes out from spreading machine automatically,and then it is got by automatic machine of cutting and punching. The machine of automatic cuting and punching is equiped with hole mold and cuting shear ,which can be used to punch and cutting steel sheet.And then automatically droped onto the trolly plat. After collecting a full of cart,the worked pieces will be sent to the next procedures ,for forming or for deep-drawing. The machines are controlled by computer,count pieces number automatically,no or less worker to take care of it. The material thickness which can be processed is from 0.5mm to 5mm,and the width can be from 10mm to 800mm.The matericals which can be process is steel sheet,stainless steel sheet,aluminium sheet,copper sheet. By this working technology,our working effience can be raised much.Working time is less than 80% and get more high precision.Especially, workers will be more safe when he is working/operating machine

 

Steel sheet stamping

Steel Sheet Mechanical punching

We owned traditional mechanical punching machines from 10Ton to 250Ton to process various sheet metal products with different thickness. Punching is the most effective but cheapest process technology to make holes in metal strip or sheet metal.It is equiped with dies/molds to create multiple shaped holes of different dimension.Punches and dies are usually fabricated from conventional tool steel or carbides. Mold/die is made by ourselves,as we have a workshop to process fabrication of mold/die professionally. The material thickness which can be processed is from 0.5mm to 5mm,and the width can be from 10mm to 1000mm.The matericals which can be process is steel sheet,stainless steel sheet,aluminium sheet,copper sheet.

 

 

 

Steel sheet stamping Steel sheet CNC stamping

We are equiped with CNC punching machine which is utilizing computer to control machine to process stamping on workpiece.CNC is the latest equipment available in the industry, such as water jet, laser and other cutting edge technology. Coupled with heavy plate capabilities and certified welding services, we are proud to bring you good service to custom sheet metal fabrication. From high volume production to prototypes, no job is too big or too small. If you have sample or drawing which want to be customed to produce metal products,just send it to us,we`ll study it and quote to you.Providing complete solution for high quality custom sheet metal fabrication, assembly and finishing. We take pride in working closely with our customers in order to provide the highest level of service.

 

 

The material thickness which can be processed is from 0.5mm to 3mm,and the width can be from 50mm to 2000mm.The matericals which can be process is steel sheet,stainless steel sheet(the thickness of stainless steel sheet to process is 1.8mm max.),aluminium sheet,copper sheet. CNC stamping is most precise to process sheet metal products,as it is controled by computer automatically. We have 2 set of CNC stamping machines to process your products and Steel sheet stamping.

 

 

 

Steel sheet stamping

Steel sheet CNC bending

Steel sheet CNC bending is a process to bend sheet metal to an angle product, typically a V shaped punch and die(from degree 20to degree 160). The steel sheet is usually put between the punch and die which presses down on the sheet. CNC bending provides a low cost method to product 3D shapes from 2D sheets. CNC bending is a suitable for processing most ductile metals and primarily for sheet metal designs with one or more bends. it can brackets,supports,cabinets,enclosures, frames,chassis, etc. There is generally no special tooling required for CNC bending, with the exception of intricate designs and special bends. At present,we owned 2set of steel sheet CNC bending machines to process your metal products and Steel sheet stamping products.

 

 

 

formingSteel sheet forming

Sheet metal forming means the processes of force is applied to a piece of sheet metal to modify its geometry rather than remove any material. The applied force stresses the metal beyond its yield strength, causing the material to plastically deform, but not to fail. The usual machine to do above fabrication mainly is Hydraulic press machine.By doing so with Hydraulic press machine, the sheet can be bent or stretched into a variety of complex shapes. Sheet metal forming processes include the following:Bending,Roll forming,Spinning,Deep Drawing and Stretch forming. At present,we owned 6set of Hydraulic press machine from 100Ton to 315Ton to process your metal products and Steel sheet stamping.

 

 

 

 

Mechanical automatic Steel sheet stamping Metalhelper is equiped with Mechanical automatic Steel sheet Stamping machine which is utilizing fixed program to process sheet metal punching or deep drawing or forming on metal workpiece.Mechanical automatic Stamping  is the updated  technology from traditional punching technology.Automatic Stamping is more widely used in todays industrybecause of its high effience and less worker cost.Usually,it can save 80% worker cost,compared with traditional punching machine. Coupled with heavy plate capabilities and certified welding services, we are proud to bring you good service to custom sheet metal fabrication. From high volume production to prototypes, no job is too big or too small. If you have sample or drawing which want to be customed to produce metal products,just send it to us,we`ll study it and quote to you.Providing complete solution for high quality custom sheet metal fabrication, assembly and finishing. We take pride in working closely with our customers in order to provide the highest level of service.

 General Knowledge on “Metal Stamping Parts”

Stamping is imposed by the press and die for sheet, strip, tubing and profiles and other external forces, thus producing plastic deformation or separation, to obtain the desired shape and size of the workpiece (stamping) of forming methods. Stamping and forging are both plastic processing (or pressure processing), collectively known as forging. Stamping blanks are mainly hot-rolled and cold rolled steel sheet and strip.

Stamping Compared with castings, forgings, with a thin, uniform, light, strong features. Punching the workpiece can be made with ribs, ribs, undulations or other method of flanging difficult to manufacture, in order to improve its rigidity. As a result of precision molds, precision workpieces up to micron level, and high repeatability and consistent specification, can punch a hole nest, bosses and so on.

Cold stamping generally no longer by cutting, or require only a small amount of cutting. Hot stamping accuracy and surface state less than cold stamping, but still better than castings, forgings, machining less.

Stamping is a highly efficient method of producing composite mold, especially multi-position progressive die stamping process can be completed more channels on a single press, implemented by the strip uncoiling, leveling, blanking the forming, finishing the whole automated production. High efficiency, good working conditions, low production cost, generally produce hundreds per minute.

Stamping mainly by technology classification, separation process can be divided into two categories and forming process. Separation step, also known as blanking, stamping its purpose is to make the separation from the sheet along a given contour line, while maintaining the quality requirements of the separation section. Surface and internal performance stamping sheet metal stamping impact on the quality of the finished product is large, require precise stamping material thickness, uniformity; smooth surface, no spots, no scars, no bruises, no surface cracks; uniform yield strength, no significant directionality; uniform elongation; yield ratio is low; hardening is low.

Commen material for stamping:

1. Galvanized steel SPCC
SECC substrates for general cold rolled steel coils, galvanized in a continuous production line after degreasing, pickling, electroplating and various post-treatment process, it becomes galvanized products. SECC only has the mechanical properties of cold-rolled steel sheet and approximate general workability, and has excellent corrosion resistance and decorative appearance. Has great competitive and substitutes on electronics, home appliances and furniture markets. For example, the widespread use of computer chassis is SPCC.
2. Ordinary SPCC cold rolled sheet
SPCC refers to the continuous cold rolling mill rolling ingot through a desired thickness steel roll or sheet material. SPCC surface without any protection, exposure to easily oxidized in air, oxidation speed, especially in humid environments, appear dark red rust, in the use of the surface to be painted, plated, or other protection.
⒊ hot-dip galvanized steel SGCC
Hot-dip galvanized steel coil refers to semi-finished products after the hot pickling or cold, after cleaning, annealing temperature of about 460 ° C immersed in molten zinc bath, leaving the steel coated with zinc layer, and then quenched leveling and chemical treatment is made. SGCC material material harder than the SECC, ductility (avoid deep drawing design), zinc layer is thick, welded poor.
4. Stainless steel SUS304
One of the most widely used stainless steel, because it contains Ni (nickel) so than containing Cr (chromium) steel richer corrosion resistance, heat resistance, and has a very good mechanical properties, non-hardening heat treatment, there is no flexibility.
5. Stainless steel SUS301
(Cr) Cr content lower than the SUS304, corrosion resistance is poor, but after punching in the cold to get a good tension and hardness, good elasticity, and more for shrapnel springs and anti-EMI.

Submit drawings for Customing Metal Stamping Parts,Let Smartclima manufacture it for you

prder procedures

Request Quotation for Custom Metal Stamping Parts,Let China metal factory serve for you:

[contact-form-7 id=”19″ title=”Contact form 1″] Metal Stamping for many fieldsMetal Products Fabricate In China  >> Sheet Metal Stamping >>Custom Metal Stamping Parts